DS3104GN Maxim Integrated Products, DS3104GN Datasheet - Page 51
DS3104GN
Manufacturer Part Number
DS3104GN
Description
Timers & Support Products SDH-SONET-Synchronou s Ethernet Line Card
Manufacturer
Maxim Integrated Products
Datasheet
1.DS3104GN.pdf
(136 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS3104GN+
Manufacturer:
Microsemi Consumer Medical Product Group
Quantity:
10 000
Part Number:
DS3104GN+
Manufacturer:
DALLAS
Quantity:
20 000
- Current page: 51 of 136
- Download datasheet (697Kb)
________________________________________________________________________________________ DS3104-SE
7.11 Reset Logic
The device has three reset controls: the RST pin, the RST bit in MCR1, and the JTAG reset pin JTRST. The RST
pin asynchronously resets the entire device, except for the JTAG logic. When the RST pin is low all internal
registers are reset to their default values, including those fields that latch their default values from, or based on, the
states of configuration input pins when the RST goes high. The RST pin must be asserted once after power-up
while the external oscillator is stabilizing.
The MCR1:RST bit resets the entire device (except for the microprocessor interface, the JTAG logic, and the RST
bit itself), but when RST is active, the register fields with pin-programmed defaults do not latch their values from, or
based on, the corresponding input pins. Instead, these fields are reset to the default values that were latched when
the RST pin was last active.
Maxim recommends holding RST low while the external oscillator starts up and stabilizes. An incorrect reset
condition could result if RST is released before the oscillator has started up completely.
Important: System software must wait at least 100µs after reset (RST pin or RST bit) is deasserted before
initializing the device as described in Section 7.13.
7.12 Power-Supply Considerations
Due to the dual-power-supply nature of the DS3104-SE, some I/Os have parasitic diodes between a 1.8V supply
and a 3.3V supply. When ramping power supplies up or down, care must be taken to avoid forward-biasing these
diodes because it could cause latchup. Two methods are available to prevent this. The first method is to place a
Schottky diode external to the device between the 1.8V supply and the 3.3V supply to force the 3.3V supply to be
within one parasitic diode drop below the 1.8V supply (i.e., V
> V
- ~0.4V). The second method is to ramp up
DDIO
DD
the 3.3V supply first and then ramp up the 1.8V supply.
7.13 Initialization
After power-up or reset, a series of writes must be done to the DS3104-SE to tune it for optimal performance. This
series of writes is called the initialization script. Each DS3104-SE die revision has a different initialization script.
Download the latest initialization scripts from the DS3104-SE webpage at www.maxim-ic.com/DS3104-SE.
19-4627; Rev 7; 8/10
51 of 136
Related parts for DS3104GN
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Ds3104 Line Card Timing Ic With Synchronous Ethernet Support
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Line Card Timing Ic With Synchronous Ethernet Support
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products