LAN9303-ABZJ Standard Microsystem (Smsc), LAN9303-ABZJ Datasheet - Page 109
![no-image](/images/no-image-200.jpg)
LAN9303-ABZJ
Manufacturer Part Number
LAN9303-ABZJ
Description
Ethernet Switch 3-Port 10Mbps/100Mbps 56-Pin QFN EP
Manufacturer
Standard Microsystem (Smsc)
Datasheet
1.LAN9303-ABZJ.pdf
(367 pages)
Specifications of LAN9303-ABZJ
Package
56QFN EP
Phy/transceiver Interface
MII/RMII
Number Of Primary Switch Ports
3
Maximum Data Rate
100 Mbps
Vlan Support
Yes
Power Supply Type
Analog
Minimum Single Supply Voltage
3 V
Maximum Single Supply Voltage
3.6 V
Maximum Supply Current
0.19(Typ) A
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LAN9303-ABZJ
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
- Current page: 109 of 367
- Download datasheet (4Mb)
Small Form Factor Three Port 10/100 Managed Ethernet Switch with Single MII/RMII/Turbo MII
Datasheet
SMSC LAN9303/LAN9303i
8.3.3
8.3.4
C
C
A
K
A
K
S 1 0 1 0
S 1 0 1 0
I
Following the device addressing, data bytes may be read sequentially from the EEPROM by outputting
a start condition and control byte with a control code of 1010b, chip/block select bits as described in
Section
bits of data. If the EEPROM slave fails to send an acknowledge, then the sequence is aborted and
the
(E2P_CMD)
next 8-bits of data. This continues until the last desired byte is read, at which point the I
sends a no-acknowledge, followed by a stop condition.
Figure 8.3
Sequential reads are used by the EEPROM Loader. Refer to
additional information.
For a register level description of a read operation, refer to
Controller Operation," on page
I
Following the device addressing, a data byte may be written to the EEPROM by outputting the data
after receiving the acknowledge from the EEPROM. The data byte is acknowledged by the EEPROM
slave and the I
send an acknowledge, then the sequence is aborted and the
(EPC_TIMEOUT)
Following the data byte write cycle, the I
write is finished. After meeting the minimum bus free time, a start condition is sent followed by a control
byte with a control code of 1010b, chip/block select bits low, and the R/~W bit low. If the EEPROM is
finished with the byte write, it will respond with an acknowledge. Otherwise, it will respond with a no-
acknowledge and the I
occur within 30mS, a time-out occurs. The check for timeout is only performed following each no-
acknowledge, since it may be possible that the EEPROM write finished before the timeout but the
30mS expired before the poll was performed (due to the bus being used by another master).
Once the I
a stop condition, which will place the EEPROM into standby.
2
2
C EEPROM Sequential Byte Reads
C EEPROM Byte Writes
EEPROM Controller Timeout (EPC_TIMEOUT)
Control Byte
Control Byte
Chip / Block
Chip / Block
Select Bits
Select Bits
8.3.1, and the R/~W bit high. The EEPROM will respond with an acknowledge, followed by 8-
illustrates typical I
A
1
0
0 0 0
2
C master receives the acknowledge, it concludes by sending a start condition, followed by
is set. The I
A
9
A
2
8
C master finishes the write cycle with a stop condition. If the EEPROM slave fails to
1
1
R/~W
R/~W
bit in the
Figure 8.4 I
A
C
K
A
C
K
D
D
7
7
2
C master will issue a stop and repeat the poll. If the acknowledge does not
2
D
6
D
6
Double Byte Addressing Sequential Reads
Single Byte Addressing Sequential Reads
C master then sends an acknowledge, and the EEPROM responds with the
Data Byte
Data Byte
D
5
D
5
EEPROM Command Register (E2P_CMD)
2
C EEPROM sequential byte reads for single and double byte addressing.
D
D
4
4
2
111.
C EEPROM Sequential Byte Reads
D
3
D
3
D
D
2
2
DATASHEET
D
D
1
1
D
0
D
0
2
A
C
K
A
C
K
C master will poll the EEPROM to determine when the byte
109
D
7
D
7
D
6
D
6
Data Byte
Data Byte
D
D
5
5
D
D
4
4
D
3
D
3
D
2
D
2
bit in the
D
1
D
1
D
0
D
0
A
C
K
A
C
K
Section 8.3.7, "I2C Master EEPROM
...
...
Section 8.4, "EEPROM Loader"
D
7
D
7
EEPROM Command Register
EEPROM Controller Timeout
D
D
6
6
is set.
Data Byte
Data Byte
D
5
D
5
D
4
D
4
D
D
3
3
D
2
D
2
Revision 1.4 (07-07-10)
D
D
1
1
D
D
0
0
A
C
K
A
C
K
P
P
2
C master
for
Related parts for LAN9303-ABZJ
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN9311-NZW](/images/no-image3.png)
Part Number:
Description:
Ethernet Switch 2-Port 10Mbps/100Mbps 128-Pin XVTQFP
Manufacturer:
Standard Microsystem (Smsc)
Datasheet:
![LAN9311I-NZW](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Standard Microsystem (Smsc)
Datasheet: