LAN9303-ABZJ Standard Microsystem (Smsc), LAN9303-ABZJ Datasheet - Page 157
![no-image](/images/no-image-200.jpg)
LAN9303-ABZJ
Manufacturer Part Number
LAN9303-ABZJ
Description
Ethernet Switch 3-Port 10Mbps/100Mbps 56-Pin QFN EP
Manufacturer
Standard Microsystem (Smsc)
Datasheet
1.LAN9303-ABZJ.pdf
(367 pages)
Specifications of LAN9303-ABZJ
Package
56QFN EP
Phy/transceiver Interface
MII/RMII
Number Of Primary Switch Ports
3
Maximum Data Rate
100 Mbps
Vlan Support
Yes
Power Supply Type
Analog
Minimum Single Supply Voltage
3 V
Maximum Single Supply Voltage
3.6 V
Maximum Supply Current
0.19(Typ) A
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LAN9303-ABZJ
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
- Current page: 157 of 367
- Download datasheet (4Mb)
Small Form Factor Three Port 10/100 Managed Ethernet Switch with Single MII/RMII/Turbo MII
Datasheet
SMSC LAN9303/LAN9303i
BITS
0
Port 0 Full-Duplex Manual Flow Control Select (MANUAL_FC_0)
This bit toggles flow control selection between manual and auto-negotiation.
0: If auto-negotiation is enabled, the auto-negotiation function
determines the flow control of switch Port 0 (RX_FC_0 and TX_FC_0
values ignored). If auto-negotiation is disabled, the RX_FC_0 and
TX_FC_0 values are used.
1: TX_FC_0 and RX_FC_0 bits determine the flow control of switch Port
0 when in full-duplex mode
Note:
Note 13.12 The default value of this field is determined by the
Note 13.13 The default value of this bit is determined by multiple strap settings. The strap values are
Note 13.14 The default value of this field is determined by the
Note 13.15 This bit is RO when in MAC mode.
Note 13.16 The default value of this field is determined by the
In MAC mode, this bit is forced high. The Virtual PHY is not
applicable in this mode and full-duplex flow control should be
controlled manually by the host based on the external PHYs Auto-
Negotiation results.
strap value is loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the value, this register is updated with the new values. See
Section 4.2.4, "Configuration Straps," on page 45
loaded during reset and can be re-written by the EEPROM Loader. Once the EEPROM
Loader re-writes the values, this register is updated with the new values. Refer to
6.2.3, "Flow Control Enable Logic," on page 62
strap value is loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the value, this register is updated with the new values. See
Section 4.2.4, "Configuration Straps," on page 45
The strap value is loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the value, this register is updated with the new values. In
MAC mode, this bit is not re-written by the EEPROM Loader and has a default value of
“1”. See
Section 4.2.4, "Configuration Straps," on page 45
DESCRIPTION
DATASHEET
157
for additional information.
BP_EN_strap_0
FD_FC_strap_0
manual_FC_strap_0
for more information.
for more information.
for more information.
Note 13.15
TYPE
R/W
configuration strap. The
configuration strap. The
Revision 1.4 (07-07-10)
configuration strap.
Note 13.16
DEFAULT
Section
Related parts for LAN9303-ABZJ
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN9311-NZW](/images/no-image3.png)
Part Number:
Description:
Ethernet Switch 2-Port 10Mbps/100Mbps 128-Pin XVTQFP
Manufacturer:
Standard Microsystem (Smsc)
Datasheet:
![LAN9311I-NZW](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Standard Microsystem (Smsc)
Datasheet: