IDT5T9306NLI IDT, Integrated Device Technology Inc, IDT5T9306NLI Datasheet - Page 6

• Manufacturer Part Number: IDT5T9306NLI
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Clock Driverr

Specifications of IDT5T9306NLI

• Number Of Clock Inputs: 2
• Mode Of Operation: Differential
• Output Frequency: 1000MHz
• Output Logic Level: LVDS
• Operating Supply Voltage (min): 2.3V
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 2.7V
• Package Type: VFQFPN
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Quiescent Current: 240mA
• Lead Free Status / RoHS Status: Not Compliant

AC DIFFERENTIAL INPUT SPECIFICATIONS
NOTES:
1. The output will not change state until the inputs have crossed and the minimum differential voltage range defined by V
2. V
3. V
POWER SUPPLY CHARACTERISTICS FOR LVDS OUTPUTS
IDT
DIFFERENTIAL INPUT AC TEST CONDITIONS FOR LVDS
NOTES:
1. The 400mV peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V
2. A 1.2V crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V
3. In all cases, input waveform timing is marked at the differential cross-point of the input signals.
4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.
NOTES:
1. These power consumption characteristics are for all the valid input interfaces and cover the worst case conditions.
2. The true input is held LOW and the complementary input is held HIGH.
Symbol
Symbol
must be achieved to guarantee switching to a new state.
IDT5T9306
2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II
Symbol
specification under actual use conditions.
actual use conditions.
™
DIF
CM
I
t
V
V
I
V
V
V
DDQ
V
I
R
TOT
/ ICS
V
D
PD
DIF
CM
DIF
THI
, t
IX
IN
specifies the minimum input voltage (V
specifies the maximum allowable range of (V
X
H
F
™
LVDS CLOCK BUFFER TERABUFFER™ II
Quiescent V
Total Power V
Total Power Down Supply Current
Parameter
Input Signal Swing
Differential Input Signal Crossing Point
Duty Cycle
Input Timing Measurement Reference Level
Input Signal Edge Rate
Parameter
Parameter
AC Differential Voltage
Differential Input Crosspoint Voltage
Common Mode Input Voltage Range
Input Voltage
DD
DD
Power Supply Current
Supply Current
(1)
TR
(4)
- V
CP
(2)
TR
) required for switching where V
+ V
CP
) /2.
(2)
V
Outputs enabled
V
PD = LOW
(3)
DD
DD
(3)
= Max., All Input Clocks = LOW
= 2.7V., F
Test Conditions
REFERENCE CLOCK
TR
is the "true" input level and V
6
(1)
= 1GHz
(2)
CP
is the "complement" input level. The AC differential voltage
Min.
- 0.3
0.05
0.05
DIF
0.1
has been met or exceeded.
(1)
IDT5T9306 REV. B October 21, 2008
Crossing Point
Typ.
Typ.
—
—
—
—
—
—
Value
400
1.2
50
2
+3.6
Max
Max
V
V
240
250
3.6
5
DD
DD
X
specification under
Units
V/ns
mV
%
V
V
Unit
Unit
mA
mA
mA
V
V
V
V
DIF
(AC)