IDT77V126L200TFI8 IDT, Integrated Device Technology Inc, IDT77V126L200TFI8 Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT77V126L200TFI8
Manufacturer Part Number
IDT77V126L200TFI8
Description
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.IDT77V126L200TFI8.pdf
(30 pages)
Specifications of IDT77V126L200TFI8
Number Of Channels
1
Type Of Atm Phy Interface
UTOPIA
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (min)
3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Pin Count
64
Mounting
Surface Mount
Lead Free Status / RoHS Status
Not Compliant
Control and Status Interface
Utility Bus
registers within the IDT77V126L200. These registers are used to select
desired operating characteristics and functions, and to communicate
status to external systems.
bus (AD[7:0]) where the register address is latched via the Address
Latch Enable (ALE) signal.
performed as follows:
Interrupt Operations
provided. They are useful both during ‘normal’ operation, and as diag-
nostic aids. Refer to the Status and Control Register List section.
Register. When this bit is cleared (set to 0), interrupt signalling is
prevented. The Interrupt Mask Register allows individual masking of
different interrupt sources. Additional interrupt signal control is provided
by bit 5 of the Master Control Register. When this bit is set (=1), receive
cell errors will be flagged via interrupt signalling and all other interrupt
IDT77V126L200
The Utility Bus is a byte-wide interface that provides access to the
The Utility Bus is implemented using a multiplexed address and data
The Utility Bus interface is comprised of the following pins:
AD[7:0], ALE, CS, RD, WR
Read Operation
Refer to the Utility Bus timing waveforms. A register read is
1. Initial condition:
2. Set up register address:
3. Read register data:
Write Operation
A register write is performed as described below:
1. Initial condition:
2. Set up register address:
3. Write data:
A variety of selectable interrupt and signalling conditions are
Overall interrupt control is provided via bit 0 of the Master Control
– RD, WR, CS not asserted (logic 1)
– ALE not asserted (logic 0)
– place desired register address on AD[7:0]
– set ALE to logic 1;
– latch this address by setting ALE to logic 0.
– Remove register address data from AD[7:0]
– assert CS by setting to logic 0;
– assert RD by setting to logic 0
– wait minimum pulse width time (see AC specifications)
– RD, WR, CS not asserted (logic 1)
– ALE not asserted (logic 0)
– place desired register address on AD[7:0]
– set ALE to logic 1;
– latch this address by setting ALE to logic 0.
– place data on AD[7:0]
– assert CS by setting to logic 0;
– assert WR (logic 0) for minimum time (according to timing
specification); reset WR or CS to logic 1 to complete register
write cycle.
13 of 30
conditions are masked. These errors include:
clearing bit 5 in the Master Control Register. INT (pin 34) will go to a
low state when an interrupt condition is detected. The external system
should then interrogate the 77V126L200 to determine which one (or
more) conditions caused this flag, and reset the interrupt for further
occurrences. This is accomplished by reading the Interrupt Status
Register. Decoding the bits in this byte will tell which error condition
caused the interrupt. Reading this register also:
problems.
LED Control and Signaling
As an example, the RxLED outputs are described in the truth table:
two-LED condition indicator. These could also be different colors to
provide simple status indication at a glance. (The minimum value for R
should be 330 ).
TxLED Truth Table
Diagnostic Functions
Normal interrupt operations are performed by setting bit 0 and
This leaves the interrupt system ready to signal an alarm for further
The LED outputs provide bi-directional LED drive capability of 8 mA.
As illustrated in Figure 11, this could be connected to provide for a
!
!
!
!
!
Bad receive HEC
Short (fewer than 53 bytes) cells
Received cell symbol error
clears the (sticky) interrupt status bits in the registers that are
read
resets INT
Cells being received
Cells not being received
Cells being transmitted
Cells not being transmitted
RXLED
TXLED
State
State
Figure 11 LED Indicator
R
R
3.3V
not being received or
(Indicates: Cells are
Low
High
Low
High
being received or
(Indicates: Cells
transmitted)
Pin Voltage
Pin Voltage
transmitted)
3505 drw 32
December 2004