UJA1065TW/3V3-T NXP Semiconductors, UJA1065TW/3V3-T Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
UJA1065TW/3V3-T
Manufacturer Part Number
UJA1065TW/3V3-T
Description
Network Controller & Processor ICs HI SPEED CAN SYSTEM
Manufacturer
NXP Semiconductors
Datasheet
1.UJA1065TW3V3-T.pdf
(76 pages)
Specifications of UJA1065TW/3V3-T
Number Of Transceivers
1
Power Down Mode
Standby
Operating Supply Voltage (min)
5.5V
Supply Current
10mA
Operating Temperature (max)
125C
Operating Temperature (min)
-40C
Operating Temperature Classification
Automotive
Mounting
Surface Mount
Product
Controller Area Network (CAN)
Data Rate
20 Kbps
Supply Voltage (max)
27 V, 52 V
Supply Voltage (min)
5.5 V
Supply Current (max)
10 mA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Package / Case
HTSSOP EP
Lead Free Status / RoHS Status
Compliant
Other names
UJA1065TW/3V3,518
NXP Semiconductors
Table 7.
[1]
UJA1065_7
Product data sheet
Bit
11 to 8
7
6
5
4
3
2
0
1
The RSS bits are updated with each reset event and not cleared. The last reset event is captured.
System Status register bit description
Symbol
RSS[3:0]
CWS
LWS
EWS
WLS
TWS
SDMS
ENS
PWONS
Description
Reset Source
CAN Wake-up Status
LIN Wake-up Status
Edge Wake-up Status
WAKE Level Status
Temperature Warning
Status
Software Development
Mode Status
Enable Status
Power-on reset Status
[1]
Rev. 07 — 25 February 2010
…continued
Value
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
Function
power-on reset; first connection of BAT42 or BAT42 below
power-on voltage threshold or RSTN was forced LOW
externally
cyclic wake-up out of Sleep mode
low V1 supply; V1 has dropped below the selected reset
threshold
V1 current above threshold within Standby mode while
watchdog OFF behavior and reset option (V1CMC bit) are
selected
V3 voltage is down due to overload occurring during Sleep
mode
SBC successfully left Flash mode
SBC ready to enter Flash mode
CAN wake-up event
LIN wake-up event
local wake-up event (via pin WAKE)
wake-up out of Fail-safe mode
watchdog overflow
watchdog not initialized in time; t
watchdog triggered too early; window missed
illegal SPI access
interrupt not served within t
CAN wake-up detected; cleared upon read
no CAN wake-up
LIN wake-up detected; cleared upon read
no LIN wake-up
pin WAKE negative edge detected; cleared upon read
pin WAKE no edge detected
pin WAKE above threshold
pin WAKE below threshold
chip temperature exceeds the warning limit
chip temperature is below the warning limit
Software Development mode on
Software Development mode off
pin EN output activated (V1-related HIGH level)
pin EN output released (LOW level)
power-on reset; cleared after a successfully entered
Normal mode
no power-on reset
High-speed CAN/LIN fail-safe system basis chip
RSTN(INT)
WD(init)
UJA1065
exceeded
© NXP B.V. 2010. All rights reserved.
33 of 76