UJA1065TW/3V3-T NXP Semiconductors, UJA1065TW/3V3-T Datasheet - Page 39
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
UJA1065TW/3V3-T
Manufacturer Part Number
UJA1065TW/3V3-T
Description
Network Controller & Processor ICs HI SPEED CAN SYSTEM
Manufacturer
NXP Semiconductors
Datasheet
1.UJA1065TW3V3-T.pdf
(76 pages)
Specifications of UJA1065TW/3V3-T
Number Of Transceivers
1
Power Down Mode
Standby
Operating Supply Voltage (min)
5.5V
Supply Current
10mA
Operating Temperature (max)
125C
Operating Temperature (min)
-40C
Operating Temperature Classification
Automotive
Mounting
Surface Mount
Product
Controller Area Network (CAN)
Data Rate
20 Kbps
Supply Voltage (max)
27 V, 52 V
Supply Voltage (min)
5.5 V
Supply Current (max)
10 mA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Package / Case
HTSSOP EP
Lead Free Status / RoHS Status
Compliant
Other names
UJA1065TW/3V3,518
NXP Semiconductors
Table 12.
[1]
[2]
UJA1065_7
Product data sheet
Bit
15 and 14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
For the CAN transceiver to enter Off-Line mode from On-line or On-line Listen mode a minimum time without bus activity is needed. This
minimum time t
In case of an RXDC / TXDC interfacing failure the CAN transmitter is disabled without setting CTC. Recovery from such a failure is
automatic when CAN communication (with correct interfacing levels) is received. Manual recovery is also possible by setting and
clearing the CTC bit under software control.
Physical Layer Control and Physical Layer Control Feedback register bit description
Symbol
A1, A0
RRS
RO
V2C
CPNC
COTC
CTC
CRC
CMC
CSC
LMC
LSC
LDC
LWEN
LTC
6.13.9 Physical Layer Control register and Physical Layer Control Feedback
off-line
is defined by COTC; see
register
These registers allow configuration of the CAN transceiver and LIN transceiver of the SBC
and allow the settings to be read back.
Description
register address
Read Register Select
Read Only
V2 Control
CAN Partial Networking
Control
CAN Off-line Time
Control
CAN Transmitter
Control
CAN Receiver Control
CAN Mode Control
CAN Split Control
LIN Mode Control
LIN Slope Control
LIN Driver Control
LIN Wake-up Enable
LIN Transmitter
Control
[1]
[2]
[3]
Section
Rev. 07 — 25 February 2010
6.7.1.4.
Value
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
11
1
Function
select Physical Layer Control register
read the General Purpose Feedback register 1
read the Physical Layer Control Feedback register
read the register selected by RRS without writing to the
Physical Layer Control register
read the register selected by RRS and write to Physical
Layer Control register
V2 remains active in CAN Off-line mode
V2 is OFF in CAN Off-line mode
CAN transceiver enters On-line Listen mode instead of
On-line mode; cleared whenever the SBC enters On-line
mode or Active mode
On-line Listen mode disabled
t
t
CAN transmitter is disabled
CAN transmitter is enabled
TXD signal is forwarded directly to RXD for self-test
purposes (loopback behavior); only if CTC = 1
TXD signal is not forwarded to RXD (normal behavior)
CAN Active mode (in Normal mode and Flash mode only)
CAN Active mode disabled
CAN SPLIT pin active
CAN SPLIT pin floating
LIN Active mode (in Normal mode and Flash mode only)
LIN Active mode disabled
up to 10.4 kbit/s (low slope)
up to 20 kbit/s (normal)
increased LIN driver current capability
LIN driver in conformance with the LIN 2.0 standard
wake-up via the LIN-bus enabled
wake-up via the LIN-bus disabled
LIN transmitter is disabled
LIN transmitter is enabled
off-line
off-line
High-speed CAN/LIN fail-safe system basis chip
long period (extended to t
short period (extended to t
off-line(ext)
off-line(ext)
UJA1065
© NXP B.V. 2010. All rights reserved.
after wake-up)
after wake-up)
39 of 76