IDTICS1893CFLFT IDT, Integrated Device Technology Inc, IDTICS1893CFLFT Datasheet - Page 47

• Manufacturer Part Number: IDTICS1893CFLFT
• Manufacturer: IDT, Integrated Device Technology Inc

Specifications of IDTICS1893CFLFT

• Lead Free Status / RoHS Status: Compliant

7.2.2 Loopback Enable (bit 0.14)
7.2.3 Data Rate Select (bit 0.13)
7.2.4 Auto-Negotiation Enable (bit 0.12)
ICS1893CF, Rev. J, 08/11/09
This bit controls the Loopback mode for the ICS1893CF. Setting this bit to logic:
•
•
This bit provides a means of controlling the ICS1893CF data rate. Its operation depends on the state of
several other functions, including the HW/SW input pin and the Auto-Negotiation Enable bit (bit 0.12).
When the ICS1893CF is configured for:
•
•
This bit provides a means of controlling the ICS1893CF Auto-Negotiation sublayer. Its operation depends
on the HW/SW input pin.
When the ICS1893CF is configured for:
•
•
Zero disables the Loopback mode.
One enables the Loopback mode by disabling the Twisted-Pair Transmitter, the Twisted-Pair Receiver,
and the collision detection circuitry. (The STA can override the ICS1893CF from disabling the collision
detection circuitry in Loopback mode by writing logic one to bit 0.7.) When the ICS1893CF is in
Loopback mode, the data presented at the MAC transmit interface is internally looped back to the MAC
receive interface. The delay from the assertion of Transmit Data Enable (TXEN) to the assertion of
Receive Data valid (RXDV) is less than 512 bit times.
Hardware mode (that is, the HW/SW pin is logic zero), the ICS1893CF isolates this bit 0.13 and uses the
10/100SEL input pin to establish the data rate for the ICS1893CF. In this Hardware mode:
Software mode (that is, the HW/SW pin is logic one), the function of bit 0.13 depends on the
Auto-Negotiation Enable bit 0.12. When the Auto-Negotiation sublayer is:
Hardware mode, (that is, the HW/SW pin is logic zero), the ICS1893CF isolates bit 0.12 and uses the
ANSEL (Auto-Negotiation Select) input pin to determine whether to enable the Auto-Negotiation
sublayer.
Note: In Hardware mode, bit 0.12 is undefined.
Software mode, (that is, the HW/SW pin is logic one), bit 0.12 determines whether to enable the
Auto-Negotiation sublayer. When bit 0.12 is logic:
– Bit 0.13 is undefined.
– The ICS1893CF provides a Data Rate Status bit (in the QuickPoll Detailed Status Register, bit
– Enabled, the ICS1893CF isolates bit 0.13 and relies on the results of the auto-negotiation process to
– Disabled, bit 0.13 determines the data rate. In this case, setting bit 0.13 to logic:
– Zero:
– One:
17.15), which always shows the setting of an active link.
establish the data rate.
• Zero selects 10-Mbps ICS1893CF operations.
• One selects 100-Mbps ICS1893CF operations.
• The ICS1893CF disables the Auto-Negotiation sublayer.
• The ICS1893CF bit 0.13 (the Data Rate bit) and bit 0.8 (the Duplex Mode bit) determine the data
• The ICS1893CF enables the Auto-Negotiation sublayer.
• The ICS1893CF isolates bit 0.13 and bit 0.8.
ICS1893CF Data Sheet Rev. J - Release
rate and the duplex mode.
Copyright © 2009, Integrated Device Technology, Inc.
All rights reserved.
47
Chapter 7 Management Register Set
August, 2009