ICS1892Y-10T IDT, Integrated Device Technology Inc, ICS1892Y-10T Datasheet - Page 24
ICS1892Y-10T
Manufacturer Part Number
ICS1892Y-10T
Description
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.ICS1892Y-10T.pdf
(148 pages)
Specifications of ICS1892Y-10T
Lead Free Status / RoHS Status
Not Compliant
- Current page: 24 of 148
- Download datasheet (690Kb)
6.1 MII Data Interface
ICS1892, Rev. D, 2/26/01
The most common configuration for the ICS1892 MAC/Repeater Interface is to configure the
MAC/Repeater Interface as a Medium Independent Interface (MII) operating at either 10 Mbps or 100 Mbps
(depending on the configuration). When the MAC/Repeater Interface is configured for the MII Data
Interface mode, the MAC/Repeater Interface is used to transfer between the ICS1892 and the
MAC/repeater framed, 4-bit parallel nibbles, along with control and status signals.
The ICS1892 implements an MII that is fully compliant with the IEEE Std 802.3u when connecting to MACs
or repeaters. The ICS1892 MII supports a variety of interfaces to MACs and repeaters, which can occur as
follows:
•
•
•
Clause 22 of the ISO/IEC standard defines the MII between an Ethernet PHY and the MAC/Reconciliation
sublayer for 10-Mbps and 100-Mbps operations. The specification supports a variety of physical media,
including 100Base-TX, 100Base-T4, and 100Base-FX. The specification is such that use of a specific
medium for the Link Segment is transparent to the MAC. The ICS1892 supports this definition for both
100Base-TX and 10Base-T operations.
The ISO/IEC-specified MII has both a transmit and a receive data path. Each data path can synchronously
exchange 4 bits of data (that is, nibbles).
•
•
Both the transmit clock and the receive clock are provided to the MAC/Reconciliation sublayer by the
ICS1892 (that is, the ICS1892 sources the TXCLK and RXCLK signals).
Clause 22 also defines as part of the MII a Carrier Sense signal (CRS) and a Collision Detect signal (COL).
The ICS1892 is fully compliant with these definitions and sources both of these signals to the
MAC/repeater. When operating in:
•
•
As mentioned in
it is possible to connect its MII to a MAC when power is already applied to the MAC. To support this
functionality, the ICS1892 isolates its MII signals and tri-states the signals on the Twisted-Pair Transmit
pins (TP_TXP and TP_TXN) during a power-on reset. Upon completion of the reset process, the ICS1892
enables its MII and enables its Twisted-Pair Transmit signals.
On the same board (that is chip to chip)
On a motherboard to a daughterboard
Through an MII connector and cable (in a manner similar to AUI connections)
The transmit data path includes the following:
The receive data path includes the following:
Half-duplex mode, the ICS1892 asserts the Carrier Sense signal when data is being either transmitted or
received. While operating in half-duplex mode, the ICS1892 also asserts the Collision Detect signal to
indicate that data is being received while a transmission is in progress.
Full-duplex mode, the ICS1892 asserts the Carrier Sense signal only when receiving data and forces the
Collision Detect signal to remain inactive.
– A data nibble, TXD[3:0]
– A transmit data clock to synchronize transfers, TXCLK
– A transmit enable signal, TXEN
– A transmit error signal, TXER
– A separate data nibble, RXD[3:0]
– A receive data clock to synchronize transfers, RXCLK
– A receive data valid signal, RXDV
– A receive error signal, RXER
ICS1892 Data Sheet
Section 5.1.1.3, “Hot
© 2000-2001, Integrated Circuit Systems, Inc.
All rights reserved.
Insertion”, the ICS1892 design allows hot insertion of its MII. That is,
24
Chapter 6 Interface Overviews
February 26, 2001
Related parts for ICS1892Y-10T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
TRANSLATION DEVICE DPI 80-PQFP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
IDT PART
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
IC LIU T1/E1/J1 OCTAL 256PBGA
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
IC FREQ TIMING GENERATOR 28TSSOP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
IC CLK DVR PLL 1:10 40VFQFPN
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
IC CLK FANOUT BUFFER 1:18 32LQFP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
IC CLK FANOUT BUFFER 1:18 32LQFP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
IC CK505 VREG/RES 56TSSOP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
IC SDRAM CLK DVR 1:10 48-TSSOP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
IC CLK DVR PLL 1:10 48TSSOP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet: