PIC16F1518-E/SP Microchip Technology, PIC16F1518-E/SP Datasheet - Page 87

• Manufacturer Part Number: PIC16F1518-E/SP
• Description: 28-pin, 28KB Flash, 1024B RAM, 10-bit ADC, 2xCCP, SPI, MI2C, EUSART, 2.3V-5.5V 2
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1518-E/SP

• Processor Series: PIC16F151x
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 16 KB
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 3
• Operating Supply Voltage: 2.3 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• Package / Case: PDIP-28
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: -
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 5.5 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Lead Free Status / Rohs Status: Details

8.0
The Power-Down mode is entered by executing a
SLEEP instruction.
Upon entering Sleep mode, the following conditions
exist:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Refer to individual chapters for more details on
peripheral operation during Sleep.
To minimize current consumption, the following condi-
tions should be considered:
• I/O pins should not be floating
• External circuitry sinking current from I/O pins
• Internal circuitry sourcing current from I/O pins
• Current draw from pins with internal weak pull-ups
• Modules using 31 kHz LFINTOSC
• Modules using secondary oscillator
I/O pins that are high-impedance inputs should be
pulled to V
currents caused by floating inputs.
The FVR module is an example of internal circuitry that
might be sourcing current. See
Voltage Reference (FVR)”
module.
 2011 Microchip Technology Inc.
WDT will be cleared but keeps running, if
enabled for operation during Sleep.
PD bit of the STATUS register is cleared.
TO bit of the STATUS register is set.
CPU clock is disabled.
31 kHz LFINTOSC is unaffected and peripherals
that operate from it may continue operation in
Sleep.
Secondary Oscillator is unaffected and periph-
erals that operate from it may continue operation
in Sleep.
ADC is unaffected, if the dedicated FRC clock is
selected.
I/O ports maintain the status they had before
SLEEP was executed (driving high, low or high-
impedance).
Resets other than WDT are not affected by
Sleep mode.
POWER-DOWN MODE (SLEEP)
DD
or V
SS
externally to avoid switching
for more information on this
Section 14.0 “Fixed
Preliminary
8.1
The device can wake-up from Sleep through one of the
following events:
1.
2.
3.
4.
5.
6.
The first three events will cause a device Reset. The
last three events are considered a continuation of pro-
gram execution. To determine whether a device Reset
or wake-up event occurred, refer to
“Determining the Cause of a
When the SLEEP instruction is being executed, the next
instruction (PC + 1) is prefetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be enabled. Wake-up will
occur regardless of the state of the GIE bit. If the GIE
bit is disabled, the device continues execution at the
instruction after the SLEEP instruction. If the GIE bit is
enabled, the device executes the instruction after the
SLEEP instruction, the device will call the Interrupt Ser-
vice Routine. In cases where the execution of the
instruction following SLEEP is not desirable, the user
should have a NOP after the SLEEP instruction.
The WDT is cleared when the device wakes up from
Sleep, regardless of the source of wake-up.
PIC16(L)F1516/7/8/9
External Reset input on MCLR pin, if enabled
BOR Reset, if enabled
POR Reset
Watchdog Timer, if enabled
Any external interrupt
Interrupts by peripherals capable of running dur-
ing Sleep (see individual peripheral for more
information)
Wake-up from Sleep
Reset”.
DS41452B-page 87
Section 6.11