STM32F217ZGT6 STMicroelectronics, STM32F217ZGT6 Datasheet - Page 46

• Manufacturer Part Number: STM32F217ZGT6
• Description: MCU ARM 1024KB FLASH 144LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F217ZGT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 120MHz
• Connectivity: CAN, Ethernet, I²C, IrDA, LIN, MMC, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, LCD, POR, PWM, WDT
• Number Of I /o: 114
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 132K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 24x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Cpu Family: STM32
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 120MHz
• Total Internal Ram Size: 132KB
• # I/os (max): 114
• Number Of Timers - General Purpose: 14
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Dac: 2(2-chx12-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-11189

Pinouts and pin description
Table 5.
1. I = input, O = output, S = supply, HiZ = high impedance.
2. FT = 5 V tolerant; TT = 3.6 V tolerant.
3. Function availability depends on the chosen device.
4. PC13, PC14, PC15 and PI8 are supplied through the power switch. Since the switch only sinks a limited amount of current
5. Main function after the first backup domain power-up. Later on, it depends on the contents of the RTC registers even after
6. FT = 5 V tolerant except when in analog mode or oscillator mode (for PC14, PC15, PH0 and PH1).
7. If the device is delivered in an UFBGA176 package and if the REGOFF pin is set to V
8. FSMC_NL pin is also named FSMC_NADV on memory devices.
9. RFU means “reserved for future use”. This pin can be tied to V
46/158
-
(3 mA), the use of GPIOs PC13 to PC15 and PI8 in output mode is limited: the speed should not exceed 2 MHz with a
maximum load of 30 pF and these I/Os must not be used as a current source (e.g. to drive an LED).
reset (because these registers are not reset by the main reset). For details on how to manage these I/Os, refer to the RTC
register description sections in the STM32F20x and STM32F21x reference manual, available from the STMicroelectronics
website: www.st.com.
as an internal Reset (active low).
-
Pins
- 176 C2
STM32F21x pin and ball definitions (continued)
Pin name
PI7
I/O FT
Doc ID 17050 Rev 4
(after reset)
function
DD
Main
PI7
,V
SS
or left unconnected.
(3)
TIM8_CH3 / DCMI_D7
Alternate functions
DD
(Regulator OFF), then PA0 is used
STM32F215xx, STM32F217xx
functions
Other