IDT5T9302PGGI8 IDT, Integrated Device Technology Inc, IDT5T9302PGGI8 Datasheet - Page 8

• Manufacturer Part Number: IDT5T9302PGGI8
• Description: IC CLK BUFFER 1:2 LVDS 20-TSSOP
• Manufacturer: IDT, Integrated Device Technology Inc
• Series: TERABUFFER™ IIr
• Type: Fanout Buffer (Distribution), Multiplexerr

Specifications of IDT5T9302PGGI8

• Number Of Circuits: 1
• Ratio - Input:output: 2:2
• Differential - Input:output: Yes/Yes
• Input: CML, eHSTL, HSTL, LVDS, LVEPECL, LVPECL, LVTTL
• Output: LVDS
• Frequency - Max: 450MHz
• Voltage - Supply: 2.3 V ~ 2.7 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP
• Frequency-max: 450MHz
• Number Of Clock Inputs: 2
• Mode Of Operation: Differential
• Output Frequency: 450MHz
• Output Logic Level: LVDS
• Operating Supply Voltage (min): 2.3V
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 2.7V
• Package Type: TSSOP
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 5T9302PGGI8

Table 5D. LVDS Differential Input AC Characteristics, T
NOTE 1.The 400mV peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment
(ATE) environment. This device meets the V
NOTE 2.A 1.2V crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment.
This device meets the V
NOTE 3.In all cases, input waveform timing is marked at the differential cross-point of the input signals.
N
Table 5E. AC Differential Input Characteristics
NOTE 1.The output will not change state until the inputs have crossed and the minimum differential voltage range defined by V
been met or exceeded.
NOTE 2.V
“complement” input level. The AC differential voltage must be achieved to guarantee switching to a new state.
NOTE 3.IV
IIDT™ LVDS CLOCK BUFFER TERABUFFER™ II
Symbol
V
V
D
V
t
Symbol
V
V
V
V
OTE 4.The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.
R
IDT5T9302
2.5V LVDS 1:2 CLOCK BUFFER TERABUFFER™ II
DIF
X
THI
DIF
X
CM
IN
H
/ t
F
DIF
CM
Parameter
Input Signal Swing
Differential Input Cross Point Voltage
Duty Cycle
Input Timing Measurement Reference Level
Input Signal Edge Rate
Parameter
AC Differential Voltage
Differential Input Cross Point Voltage
Common Mode Input Voltage Range
Input Voltage
specifies the minimum input voltage (V
specified the maximum allowable range of (V
X
specification under actual use conditions.
(1)
(2)
(4)
DIF
(AC) specification under actual use conditions.
(3)
(2)
TR
(1)
– V
(3)
, T
CP
TR
A
) required for switching where V
= -40°C to 85°C
+ V
A
CP
= -40°C to 85°C
8
) /2.
Minimum
0.05
0.05
-0.3
0.1
TR
Typical
is the “true” input level and V
IDT5T9302 REV. A APRIL 29, 2008
Crossing Point
Maximum
Maximum
400
1.2
50
V
V
2
3.6
3.6
DD
DD
PRELIMINARY
CP
DIF
Units
Units
V/ns
V/ns
is the
mV
%
V
V
V
V
V
has