IDT82V3001APVG IDT, Integrated Device Technology Inc, IDT82V3001APVG Datasheet - Page 23
![IC PLL WAN W/SGL REF INP 56-SSOP](/photos/40/58/405879/idt82v3001apvg_sml.jpg)
IDT82V3001APVG
Manufacturer Part Number
IDT82V3001APVG
Description
IC PLL WAN W/SGL REF INP 56-SSOP
Manufacturer
IDT, Integrated Device Technology Inc
Type
PLL Clock Generatorr
Series
-r
Datasheet
1.IDT82V3001APVG8.pdf
(28 pages)
Specifications of IDT82V3001APVG
Input
CMOS, TTL
Output
CMOS, TTL
Frequency - Max
32.768MHz
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
56-SSOP
Frequency-max
32.768MHz
Function
Wan PLL
Operating Temperature (max)
85C
Operating Temperature (min)
-40C
Package Type
SSOP
Pin Count
56
Mounting
Surface Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
82V3001APVG
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT82V3001APVG
Manufacturer:
MARVELL
Quantity:
12 000
Company:
Part Number:
IDT82V3001APVG
Manufacturer:
IDT
Quantity:
2
Part Number:
IDT82V3001APVG
Manufacturer:
IDT
Quantity:
20 000
Table - 16 2.048 MHz Input Jitter Tolerance
*
Voltages are with respect to ground (V
Supply voltage and operating temperature are as per Recommended Operating Conditions.
Timing parameters are as per AC Electrical Characteristics - Timing Parameter Measurement Voltage Levels
TEST SPECIFICATIONS
Jitter tolerance for 1 Hz input
Jitter tolerance for 5 Hz input
Jitter tolerance for 20 Hz input
Jitter tolerance for 300 Hz input
Jitter tolerance for 400 Hz input
Jitter tolerance for 700 Hz input
Jitter tolerance for 2400 Hz input
Jitter tolerance for 10 kHz input
Jitter tolerance for 100 kHz input
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Selected reference input at ±0 ppm.
11. Selected reference input at ±32 ppm.
12. Selected reference input at ±100 ppm.
13. For Freerun Mode of ±0 ppm.
14. For Freerun Mode of ±32 ppm.
15. For Freerun Mode of ±100 ppm.
16. For capture range of ±230 ppm.
17. For capture range of ±198 ppm.
18. For capture range of ±130 ppm.
19. 25 pF capacitive load.
20. OSCi Master Clock jitter is less than 2 nspp, or 0.04 UIpp where 1 UIpp = 1/20 MHz.
21. Jitter on reference input is obtained at slightly higher input jitter amplitudes.
22. Applied jitter is sinusoidal.
23. Minimum applied input jitter magnitude to regain synchronization.
24. Loss of synchronization is obtained at slightly higher input jitter amplitudes.
25. Within 10 ms of the state, reference or input change.
26. 1 UIpp = 125 µs for 8 kHz signals.
27. 1 UIpp = 648 ns for 1.544 MHz signals.
28. 1 UIpp = 488 ns for 2.048 MHz signals.
29. 1 UIpp = 323 ns for 3.088 MHz signals.
30. 1 UIpp = 244 ns for 4.096 MHz signals.
31. 1 UIpp = 122 ns for 8.192 MHz signals.
32. 1 UIpp = 61 ns for 16.484 MHz signals.
33. 1 UIpp = 30 ns for 32.968 MHz signals.
34. No filter.
35. 40 Hz to 100 kHz bandpass filter.
36. With respect to reference input signal frequency.
37. After chip reset or TIE reset.
38. Master clock duty 40% to 60%.
39. Prior to Holdover Mode, device as in Normal Mode and phase locked.
40. With input frequency offset of 100 ppm.
Notes:
IDT82V3001A
Normal Mode selected.
Holdover Mode selected.
Freerun Mode selected.
8 kHz Frequency Mode selected.
1.544 MHz Frequency Mode selected.
2.048 MHz Frequency Mode selected.
Master clock input OSCi at 20 MHz ±0 ppm.
Master clock input OSCi at 20 MHz ±32 ppm.
Master clock input OSCi at 20 MHz ±100 ppm.
Description
SS
) unless otherwise stated.
Min
150
140
130
5.5
1.3
0.4
40
33
18
Typ
23
Max
WAN PLL WITH SINGLE REFERENCE INPUT
Units
UIpp
UIpp
UIpp
UIpp
UIpp
UIpp
UIpp
UIpp
UIpp
1, 6, 7-12, 19-20, 22-24, 28
1, 6, 7-12, 19-20, 22-24, 28
1, 6, 7-12, 19-20, 22-24, 28
1, 6, 7-12, 19-20, 22-24, 28
1, 6, 7-12, 19-20, 22-24, 28
1, 6, 7-12, 19-20, 22-24, 28
1, 6, 7-12, 19-20, 22-24, 28
1, 6, 7-12, 19-20, 22-24, 28
1, 6, 7-12, 19-20, 22-24, 28
Test Conditions / Notes*
October 15, 2008