TOTX147PLF,T Toshiba, TOTX147PLF,T Datasheet

no-image

TOTX147PLF,T

Manufacturer Part Number
TOTX147PLF,T
Description
Manufacturer
Toshiba
Datasheet

Specifications of TOTX147PLF,T

Optical Fiber Type
TX
Data Transfer Rate
15Mbps
Operating Temperature Classification
Commercial
Peak Wavelength
650nm
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (typ)
3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
-20C to 70C
Mounting
Snap in
Pin Count
5
Lead Free Status / Rohs Status
Compliant
FIBER OPTIC TRANSMITTING
MODULE FOR DIGITAL AUDIO
INTERFACE
1. Absolute Maximum Ratings
2. Operating Range
Handling precaution: The LED’s used in this product contain GaAs (Gallium Arsenide).
For JEITA Standard CP−1212
LED is driven by differential circuit.
Mini-package with Shutter System
RoHS Compatible
Storage Temperature
Operating Temperature
Supply Voltage
Input Voltage
Soldering Temperature
Note 1: Soldering time ≤ 10 seconds (At a distance of 1 mm from the package).
Supply Voltage
High−Level Input Voltage
Low−Level Input Voltage
(Digital Audio Optical Interface
Characteristics
Characteristics
for Consumer Equipment).
Care must be taken to protect the safety of people and the environment when scrapping or
terminal processing.
TOTX147PL(F,T)
FIBER OPTIC TRANSMITTING MODULE
(Ta = 25°C)
Symbol
Symbol
V
V
T
T
T
V
V
V
opr
stg
CC
sol
CC
IN
IH
IL
Min
2.7
2.1
−0.5 to V
4
0
1
260 (Note 1)
3
−0.5 to 4.5
−40 to 70
−20 to 70
Rating
Typ.
3.0
---
---
CC
+ 0.5
2
Max
V
3.6
0.9
CC
5
Unit
°C
°C
°C
V
V
Unit
V
V
V
Shutter Color:Gray
Pin Connection
1. GND
2. Vcc
3. Input
4. N.C.
5. N.C.
TOTX147PL(F,T)
2006-12-28
Unit: mm

Related parts for TOTX147PLF,T

TOTX147PLF,T Summary of contents

Page 1

TOTX147PL(F,T) FIBER OPTIC TRANSMITTING MODULE FOR DIGITAL AUDIO INTERFACE For JEITA Standard CP−1212 (Digital Audio Optical Interface for Consumer Equipment). LED is driven by differential circuit. Mini-package with Shutter System RoHS Compatible 1. Absolute Maximum Ratings Characteristics Storage Temperature Operating ...

Page 2

... Note 2: LED is on when input signal is high, and off when it is low. 7.5Mb/s (max.) Biphase marked signal. Note 3: All Plastic Fiber (980 / 1000 μm). Note 4: Between input of TOTX147PL(F,T) and output of TORX147PL(F,T). Note 5: Measure with a standard optical fiber, peak value. 4. Mechanical Characteristics Characteristics Insertion Force ...

Page 3

... Note that it is not dust or waterproof. As mentioned before, optical modules are optical components. Thus, in principle, soldering where there may be flux residue and flux removal after soldering is not recommended. Toshiba recommend that soldering be performed without the optical module mounted on the board. Then, after the board has been cleaned, the optical module should be soldered on to the board manually. If the optical module cannot be soldered manually, use non− ...

Page 4

... Toshiba is continually working to improve the quality and reliability of their products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and their vulnerability to physical stress the responsibility of the buyer, when utilizing Toshiba products, to observe standards of safety, and to avoid situations in which the malfunction or failure of a Toshiba product could cause loss of human life, bodily injury or damage to property ...

Page 5

... The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • ...

Related keywords