EP1K50FC484-3 Altera, EP1K50FC484-3 Datasheet - Page 40

• Manufacturer Part Number: EP1K50FC484-3
• Description: IC ACEX 1K FPGA 50K 484-FBGA
• Manufacturer: Altera
• Series: ACEX-1K®r

Specifications of EP1K50FC484-3

• Number Of Logic Elements/cells: 2880
• Number Of Labs/clbs: 360
• Total Ram Bits: 40960
• Number Of I /o: 249
• Number Of Gates: 199000
• Voltage - Supply: 2.375 V ~ 2.625 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 484-FBGA
• Family Name: ACEX™ 1K
• Number Of Usable Gates: 50000
• Number Of Logic Blocks/elements: 2880
• # I/os (max): 249
• Frequency (max): 166.67MHz
• Process Technology: CMOS
• Operating Supply Voltage (typ): 2.5V
• Logic Cells: 2880
• Ram Bits: 40960
• Device System Gates: 199000
• Operating Supply Voltage (min): 2.375V
• Operating Supply Voltage (max): 2.625V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 484
• Package Type: FBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 544-1071

ACEX 1K Programmable Logic Device Family Data Sheet
40
PCI Pull-Up Clamping Diode Option
ACEX 1K devices have a pull-up clamping diode on every I/O, dedicated
input, and dedicated clock pin. PCI clamping diodes clamp the signal to
the V
diodes can also be used to limit overshoot in other systems.
Clamping diodes are controlled on a pin-by-pin basis. When V
3.3 V, a pin that has the clamping diode option turned on can be driven by
a 2.5-V or 3.3-V signal, but not a 5.0-V signal. When V
that has the clamping diode option turned on can be driven by a 2.5-V
signal, but not a 3.3-V or 5.0-V signal. Additionally, a clamping diode can
be activated for a subset of pins, which allows a device to bridge between
a 3.3-V PCI bus and a 5.0-V device.
Slew-Rate Control
The output buffer in each IOE has an adjustable output slew rate that can
be configured for low-noise or high-speed performance. A slower slew
rate reduces system noise and adds a maximum delay of 4.3 ns. The fast
slew rate should be used for speed-critical outputs in systems that are
adequately protected against noise. Designers can specify the slew rate
pin-by-pin or assign a default slew rate to all pins on a device-wide basis.
The slow slew rate setting affects only the falling edge of the output.
Open-Drain Output Option
ACEX 1K devices provide an optional open-drain output (electrically
equivalent to open-collector output) for each I/O pin. This open-drain
output enables the device to provide system-level control signals (e.g.,
interrupt and write enable signals) that can be asserted by any of several
devices. It can also provide an additional wired-OR plane.
MultiVolt I/O Interface
The ACEX 1K device architecture supports the MultiVolt I/O interface
feature, which allows ACEX 1K devices in all packages to interface with
systems of differing supply voltages. These devices have one set of V
pins for internal operation and input buffers (VCCINT), and another set for
I/O output drivers (VCCIO).
CCIO
value and are required for 3.3-V PCI compliance. Clamping
CCIO
Altera Corporation
is 2.5 V, a pin
CCIO
is
CC