XC4005-5PC84C Xilinx Inc, XC4005-5PC84C Datasheet - Page 39
![no-image](/images/no-image-200.jpg)
XC4005-5PC84C
Manufacturer Part Number
XC4005-5PC84C
Description
IC LOGIC CL ARRAY 5000GAT 84PLC
Manufacturer
Xilinx Inc
Series
XC4000r
Datasheet
1.XC4003-6PQ100C.pdf
(40 pages)
Specifications of XC4005-5PC84C
Number Of Logic Elements/cells
466
Number Of Labs/clbs
196
Total Ram Bits
6272
Number Of I /o
61
Number Of Gates
5000
Voltage - Supply
4.75 V ~ 5.25 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
84-LCC (J-Lead)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
122-1068
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XC4005-5PC84C
Manufacturer:
XILINX
Quantity:
210
HDC
High During Configuration is driven High until configura-
tion is completed. It is available as a control output indicat-
ing that configuration is not yet completed. After configu-
ration, this is a user-programmable I/O pin.
LDC
Low During Configuration is driven Low until configuration.
It is available as a control output indicating that configura-
tion is not yet completed. After configuration, this is a user-
programmable I/O pin.
INIT
Before and during configuration, this is a bidirectional
signal. An external pull-up resistor is recommended.
As an active-Low open-drain output, INIT is held Low
during the power stabilization and internal clearing of the
configuration memory. As an active-Low input, it can be
used to hold the LCA device in the internal WAIT state
before the start of configuration. Master mode devices stay
in a WAIT state an additional 30 to 300 s after INIT has
gone High.
During configuration, a Low on this output indicates that a
configuration data error has occurred. After configuration,
this is a user-programmable I/O pin.
PGCK1 - PGCK4
Four Primary Global Inputs each drive a dedicated internal
global net with short delay and minimal skew. If not used
for this purpose, any of these pins is a user-programmable
I/O.
SGCK1 - SGCK4
Four Secondary Global Inputs can each drive a dedicated
internal global net, that alternatively can also be driven
from internal logic. If not used for this purpose, any of these
pins is a user-programmable I/O pin.
Before and during configuration, all outputs that are not used for the configuration process are 3-stated with
a 50 k to 100 k pull-up resistor.
2-45
CS0, CS1, WS, RS
These four inputs are used in Peripheral mode. The chip
is selected when CS0 is Low and CS1 is High. While the
chip is selected, a Low on Write Strobe (WS) loads the data
present on the D0 - D7 inputs into the internal data buffer;
a Low on Read Strobe (RS) changes D7 into a status
output: High if Ready, Low if Busy, and D0…D6 are active
Low. WS and RS should be mutually exclusive, but if both
are Low simultaneously, the Write Strobe overrides. After
configuration, these are user-programmable I/O pins.
A0 - A17
During Master Parallel mode, these 18 output pins
address the configuration EPROM. After configuration,
these are user-programmable I/O pins.
D0 - D7
During Master Parallel and Peripheral configuration
modes, these eight input pins receive configuration data.
After configuration, they are user-programmable I/O pins.
DIN
During Slave Serial or Master Serial configuration modes,
this is the serial configuration data input receiving data on
the rising edge of CCLK.
During parallel configuration modes, this is the D0 input.
After configuration, DIN is a user-programmable I/O pin.
DOUT
During configuration in any mode, this is the serial configu-
ration data output that can drive the DIN of daisy-chained
slave LCA devices. DOUT data changes on the falling
edge of CCLK, one-and-a-half CCLK periods after it was
received at the DIN input. After configuration, DOUT is a
user-programmable I/O pin.
Unrestricted User-Programmable I/O Pins
I/O
A pin that can be configured to be input and/or output after
configuration is completed. Before configuration is com-
pleted, these pins have an internal high-value pull-up
resistor that defines the logic level as High.