CS42L55-DNZ Cirrus Logic Inc, CS42L55-DNZ Datasheet - Page 10

• Manufacturer Part Number: CS42L55-DNZ
• Description: IC CODEC STER H-HDPN AMP 36-QFN
• Manufacturer: Cirrus Logic Inc
• Type: Stereo Audior

Specifications of CS42L55-DNZ

• Data Interface: Serial
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 1 / 1
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 95 / 99
• Voltage - Supply, Analog: 1.65 V ~ 2.71 V
• Voltage - Supply, Digital: 1.65 V ~ 2.71 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 36-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1506 - BOARD EVAL FOR CS42L55 CODEC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

10
2. TYPICAL CONNECTION DIAGRAM
+1.65 V to +3.47 V
Notes:
1. The headphone amplifier’s output power and distortion are rated using the nominal capacitance shown. Larger capacitance
reduces the ripple on the internal amplifiers’ supplies and in turn reduces the amplifier’s distortion at high output power levels.
Smaller capacitance may not sufficiently reduce ripple to achieve the rated output power and distortion. Since the actual value
of typical X7R/X5R ceramic capacitors deviates from the nominal value by a percentage specified in the manufacturer’s data
sheet, capacitors should be selected based on the minimum output power and maximum distortion required.
2. The headphone amplifier’s output power and distortion are rated using the nominal capacitance shown and using the default
charge pump switching frequency. The required capacitance follows an inverse relationship with the charge pump’s switching
frequency. When increasing the switching frequency, the capacitance may decrease; when lowering the switching frequency,
the capacitance must increase. Since the actual value of typical X7R/X5R ceramic capacitors deviates from the nominal value
by a percentage specified in the manufacturer’s data sheet, capacitors should be selected based on the minimum output
power, maximum distortion and maximum charge pump switching frequency required.
3. Additional bulk capacitance may be added to improve PSRR at low frequencies.
4. These capacitors serve as a charge reservoir for the internal switched capacitor ADC modulators and should be placed as
close as possible to the inputs. They are only needed when the PGA (Programmable Gain Amplifier) is bypassed.
5. Input pairs (such as AIN2A, AIN2REF and AIN2B) may be left floating if they are not used.
+1.65 V to +2.71 V
Digital Audio
Processor
2 k
Ω
**
2.2 µF
2.2 µF
2.2 µF
2.2 µF
2.2 µF
Note 2
Note 1
2 k
Note 1
Ω
0.1 µF
**
**
**
Figure 1. Typical Connection Diagram
**
**
1 µF
-VHPFILT
FLYP
FLYC
FLYN
MCLK
SCLK
LRCK
SDIN
SDOUT
RESET
SCL
SDA
+VHPFILT
VCP
VL
**
VDFILT
GND/Thermal Pad
CS42L55
VLDO
**
0.1 µF
HPDETECT
LINEOUTA
LINEOUTB
LINEREF
AIN1REF
AIN2REF
HPOUTB
HPOUTA
AFILTA
AFILTB
VA
HPREF
AGND
AIN1A
AIN1B
AIN2A
AIN2B
FILT+
**
VQ
0.1 µF
0.1 µF
0.1 µF
1 µF
1 µF
**
**
562 Ω
562 Ω
**
**
1000 pF
*
33 Ω
33 Ω
1800 pF
1800 pF
1800 pF
1800 pF
47 kΩ
3300 pF
*
*
3300 pF
Note 4
1000 pF
*
*
*
*
**
*
*
LPF is Optional
Low ESR, X7R/X5R dielectric capacitors.
NPO/C0G dielectric capacitors.
1 µF
1 µF
1 µF
1 µF
**
**
**
**
+1.65 V to +2.71 V
Note 3
100 Ω
100 Ω
100 Ω
100 Ω
**
2.2 µF
100 kΩ
100 kΩ
100 kΩ
100 kΩ
2.2 µF
**
Headphone Out
Left & Right
R
R
Analog
Input 1
ext
ext
Analog
Input 2
Line Level Out
Left & Right
Note 5
CS42L55
DS773F1