CS42L55-DNZ Cirrus Logic Inc, CS42L55-DNZ Datasheet - Page 37

• Manufacturer Part Number: CS42L55-DNZ
• Description: IC CODEC STER H-HDPN AMP 36-QFN
• Manufacturer: Cirrus Logic Inc
• Type: Stereo Audior

Specifications of CS42L55-DNZ

• Data Interface: Serial
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 1 / 1
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 95 / 99
• Voltage - Supply, Analog: 1.65 V ~ 2.71 V
• Voltage - Supply, Digital: 1.65 V ~ 2.71 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 36-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1506 - BOARD EVAL FOR CS42L55 CODEC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

DS773F1
4.13
1. Write 0x99 to register 0x00.
2. Write 0x30 to register 0x2E.
3. Write 0x07 to register 0x32.
4. Write 0xFF to register 0x33.
5. Write 0xF8 to register 0x34.
6. Write 0xDC to register 0x35.
7. Write 0xFC to register 0x36.
8. Write 0xAC to register 0x37.
9. Write 0xF8 to register 0x3A.
10. Write 0xD3 to register 0x3C.
11. Write 0x23 to register 0x3D.
12. Write 0x81 to register 0x3E.
13. Write 0x46 to register 0x3F.
14. Write 0x00 to register 0x00.
Required Initialization Settings
The current required for various sections in the CODEC must be reduced using the control port compensa-
tion strategy shown below. All performance and power consumption measurements were taken with the
Control Port Compensation shown below.
3. Set bit 5 in register 07h to ‘1’b. This implements a high impedance state on the serial output ports to
4. Configure the serial port I/O control for master operation.
5. Power up either one of the ADC channels.
6. Wait 100 ms.
7. Set the PDN bit to ‘1’b. The CODEC is completely powered down in a low power state.
8. To achieve the lowest operating quiescent current, bring RESET low. All control port registers will be
signal. The zero cross timeout, however, is dependent on the serial port clock domain. Thus, to fully
power down, the ADC must briefly power up to enable the zero cross state machine. Follow the
remaining steps below to complete the power down sequence.
avoid possible contention in step
Register Controls: M/S
Register Controls: PDN_ADCx
reset to their default state.
Power Down Sequence
Step 1a ................................
Step 1b ................................
Step
Step
Step
Step
VA < 2.1 V
3
4
5
7
..................................
..................................
..................................
..................................
Register Location
“Headphone Volume Control” on page
“Headphone Channel x Mute” on page
“Miscellaneous Control (Address 07h)” on page 45
“Master/Slave Mode” on page 43
“Power Down ADC x” on page 42
“Power Down” on page 42
1. Write 0x99 to register 0x00.
2. Write 0x30 to register 0x2E.
3. Write 0x07 to register 0x32.
4. Write 0xFD to register 0x33.
5. Write 0xF8 to register 0x34.
6. Write 0xDC to register 0x35.
7. Write 0xF8 to register 0x36.
8. Write 0x6C to register 0x37.
9. Write 0xF8 to register 0x3A.
10. Write 0xD3 to register 0x3C.
11. Write 0x23 to register 0x3D.
12. Write 0x81 to register 0x3E.
13. Write 0x46 to register 0x3F.
14. Write 0x00 to register 0x00.
4
if clocks are already applied to the serial port.
VA > 2.1 V
57,
57,
“Line Volume Control” on page 58
“Line Channel x Mute” on page 58
1. [Enable test register access.]
2. Digital Regulator.
3. ADC.
4. ADC.
5. ADC.
6. Zero Cross Detector.
7. PGA.
8. PGA.
9. DAC.
10. Headphone Amplifier.
11. Headphone & Line Amplifier.
12. Line Amplifier.
13. PGA & ADC.
14. [Disable test register access.].
Current adjustments are made in
the following sections:
CS42L55
37