TDA8026ET/C2,557 NXP Semiconductors, TDA8026ET/C2,557 Datasheet - Page 25
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
TDA8026ET/C2,557
Manufacturer Part Number
TDA8026ET/C2,557
Description
IC SMART CARD SLOT 64TFBGA
Manufacturer
NXP Semiconductors
Datasheet
1.TDA8026ETC2518.pdf
(59 pages)
Specifications of TDA8026ET/C2,557
Controller Type
Smart Card Interface
Interface
I²C
Voltage - Supply
2.7 V ~ 5.5 V
Current - Supply
210mA
Operating Temperature
-25°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-TFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TDA8026ET/C2,557
Manufacturer:
NXP Semiconductors
Quantity:
10 000
NXP Semiconductors
TDA8026_1
Product data sheet
8.5.4.3 Bank 1 Register0 card slot 3 (address 03h), card slot 4 (address 04h) and card slot 5
(address 05h) write mode bit descriptions
Table 23.
[1]
[2]
[3]
Bit
7
6
5 to 4
3
2
1
0
This bit cannot be written when START bit is logic 1.
It is a mandatory condition for card slots 2 to 5 that only one card slot I/O line is enabled at a time. When
switching from one slot to another, the enabled I/O must be disabled before the I/O line for the required card
slot is enabled.
Remark: If both pins I/OUC1 and I/OUC2 are connected at the same time, this mandatory condition also
applies to card slot 1.
In synchronous mode, this bit cannot be written when START bit is logic 1.
Symbol
VCC1V8
I/OEN
REG[1:0]
PWDN
5V/3VN
WARM
START
Bank 1 Register0 card slot 3 (address 03h), card slot 4 (address 04h) and card
slot 5 (address 05h) write mode bit descriptions
[2]
[3]
All information provided in this document is subject to legal disclaimers.
[1]
[1]
Value Description
1
0
1
0
-
1
0
1
0
1
0
1
0
Rev. 1 — 9 March 2010
set to logic 1: a warm reset procedure is started
used together with the 5V/3VN bit
set to logic 1: pins I/OUCn are switched to pins I/O
set to logic 0: pins I/OUCn and I/O
internal pull-up resistor
see
slots 3 and 5 bit allocation” on page 26
set to logic 1: to apply the CLKPD[1:0] bit clock settings to pin
CLK
set to logic 0: to apply the CLKDIV[1:0] bits clock options to pin
CLK
used together with VCC1V8 bit
set to logic 0: by the hardware: a START bit is detected or the
MUTE bit is set to logic 1
set to logic 1: when the SUPL and PROT bits are logic 0 and the
PRES bit is logic 1, the activation sequence and cold reset
procedure are started
set to logic 0: deactivation sequence starts
set to logic 1: V
if set to logic 0 V
set to logic 1: and the VCC1V8 bit is logic 0: V
set to logic 0: and the VCC1V8 bit is logic 0: V
Table 24 “Bank 1 CSb[7:0] Register1 (address 42h) card
(n)
(n)
for the selected card slot
for the selected card slot
CC(n)
CC(n)
= 1.8 V; ignores the 5V/3VN bit logic state
Multiple smart card slot interface IC
is set using the 5V/3VN bit
(n)
are high-impedance with
for detailed information
TDA8026
© NXP B.V. 2010. All rights reserved.
CC(n)
CC(n)
(n)
= 5 V
= 3 V
25 of 59