CYP15G0101DXB-BBXC Cypress Semiconductor Corp, CYP15G0101DXB-BBXC Datasheet - Page 23

• Manufacturer Part Number: CYP15G0101DXB-BBXC
• Description: IC TXRX HOTLINK 100-LBGA
• Manufacturer: Cypress Semiconductor Corp
• Series: HOTlink II™r
• Type: Transceiverr

Specifications of CYP15G0101DXB-BBXC

• Package / Case: 100-LBGA
• Protocol: Fibre Channel
• Voltage - Supply: 3.135 V ~ 3.465 V
• Mounting Type: Surface Mount
• Product: PHY
• Data Rate: 1500 MBd
• Supply Voltage (max): 3.465 V
• Supply Voltage (min): 3.135 V
• Supply Current: 0.5 A
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Number Of Channels: 1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: CYP15G0101DX-EVAL - EVAL BRD FOR HOTLINK II
• Number Of Drivers/receivers: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-2920; CYP15G0101DXB-BBXC

JTAG Support
The CYP(V)(W)15G0101DXB contains a JTAG port to allow
system level diagnosis of device interconnect. Of the available
JTAG modes, only boundary scan is supported. This capability
is present only on the LVTTL inputs, LVTTL outputs and the
REFCLK clock input. The high-speed serial inputs and outputs
are not part of the JTAG test chain.
Table 16. Receive Character Status Bits
Document Number: 38-02031 Rev. *L
RXST[2:0] Priority
000
001
010
100
101
011
110
111
7
7
2
5
4
1
6
3
Normal character received. The valid data character on the output bus
meets all the formatting requirements of data characters listed in
Special code detected. The valid special character on the output bus meets
all the formatting requirements of the special code characters listed in
Table
violation indication.
Receive
Underrun/Overrun error.
The receive buffer was not able to
add/drop
character.
Framing character detected. This indicates that a character matching the
patterns identified as a framing character (as selected by FRAMCHAR) was
detected. The decoded value of this character is present on the output bus.
Codeword violation. The character on the output bus is a C0.7. This
indicates that the received character cannot be decoded into any valid
character.
PLL out of lock. This indicates a PLL out of lock condition.
Running disparity error. The character on the output bus is a C4.7, C1.7,
or C2.7.
RESERVED
21, but is not the presently selected framing character or a decoder
Type-A Status
a
elasticity
K28.5
or
framing
buffer
RESERVED
JTAG ID
The JTAG device ID for the CYP(V)(W)15G0101DXB is
“1C804069”x.
3-Level Select Inputs
Each 3-level select input reports as two bits in the scan register.
These bits report the LOW, MID, and HIGH state of the
associated input as 00, 10, and 11, respectively.
Description
Type-B Status
Table
20.
BIST data compare.
Character compared correctly
BIST
Character compared correctly
BIST last good.
Last
sequence detected and valid.
RESERVED
BIST last bad.
Last
sequence detected invalid.
BIST start. Receive BIST is
enabled on this channel, but
character compares have not
yet commenced. This also
indicates a PLL out of lock
condition, and elasticity buffer
overflow/underflow conditions.
BIST error. While comparing
characters, a mismatch was
found in one or more of the
decoded character bits.
BIST wait. The receiver is
comparing characters. but has
not yet found the start of BIST
character to enable the LFSR.
(Receive BIST = Enabled)
CYW15G0101DXB
CYP15G0101DXB
CYV15G0101DXB
Receive BIST Status
character
character
command
Page 23 of 44
of
of
compare.
BIST
BIST
[+] Feedback