PIC18F46K80-I/P Microchip Technology Inc., PIC18F46K80-I/P Datasheet - Page 328
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC18F46K80-I/P
Manufacturer Part Number
PIC18F46K80-I/P
Description
40 PDIP .600IN TUBE, ECAN, 64KB FLASH, 4KB RAM, 16 MIPS, 12-BIT ADC, CTMU
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC18F46K80-IPT.pdf
(628 pages)
Specifications of PIC18F46K80-I/P
A/d Inputs
11-Channel, 12-Bit
Comparators
2
Cpu Speed
16 MIPS
Eeprom Memory
1K Bytes
Input Output
35
Interface
I2C/SPI/UART/USART
Memory Type
Flash
Number Of Bits
8
Package Type
44-pin PDIP
Programmable Memory
64K Bytes
Ram Size
3.6K Bytes
Speed
64 MHz
Temperature Range
–40 to 125 °C
Timers
2-8-bit, 3-16-bit
Voltage, Range
1.8-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F46K80-I/PT
Manufacturer:
BROADCOM
Quantity:
101
Company:
Part Number:
PIC18F46K80-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC18F46K80-I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
- Current page: 328 of 628
- Download datasheet (6Mb)
PIC18F66K80 FAMILY
21.4.10
Transmission of a data byte, a 7-bit address or the
other half of a 10-bit address, is accomplished by
simply writing a value to the SSPBUF register. This
action will set the Buffer Full flag bit, BF, and allow the
Baud Rate Generator to begin counting and start the
next transmission. Each bit of address/data will be
shifted out onto the SDA pin after the falling edge of
SCL is asserted (see data hold time specification
Parameter 106). SCL is held low for one Baud Rate
Generator rollover count (T
before SCL is released high (see data setup time spec-
ification Parameter 107). When the SCL pin is released
high, it is held that way for T
pin must remain stable for that duration and some hold
time after the next falling edge of SCL. After the eighth
bit is shifted out (the falling edge of the eighth clock),
the BF flag is cleared and the master releases SDA.
This allows the slave device being addressed to
respond with an ACK bit during the ninth bit time if an
address match occurred, or if data was received prop-
erly. The status of ACK is written into the ACKDT bit on
the falling edge of the ninth clock. If the master receives
an
ACKSTAT, is cleared; if not, the bit is set. After the ninth
clock, the SSPIF bit is set and the master clock (Baud
Rate Generator) is suspended until the next data byte
is loaded into the SSPBUF, leaving SCL low and SDA
unchanged
After the write to the SSPBUF, each bit of the address
will be shifted out on the falling edge of SCL until all
seven address bits and the R/W bit are completed. On
the falling edge of the eighth clock, the master will
deassert the SDA pin, allowing the slave to respond
with an Acknowledge. On the falling edge of the ninth
clock, the master will sample the SDA pin to see if the
address was recognized by a slave. The status of the
ACK bit is loaded into the ACKSTAT status bit
(SSPCON2<6>). Following the falling edge of the ninth
clock transmission of the address, the SSPIF flag is
set, the BF flag is cleared and the Baud Rate Generator
is turned off until another write to the SSPBUF takes
place, holding SCL low and allowing SDA to float.
21.4.10.1
In Transmit mode, the BF bit (SSPSTAT<0>) is set
when the CPU writes to SSPBUF and is cleared when
all 8 bits are shifted out.
21.4.10.2
If the user writes the SSPBUF when a transmit is
already in progress (i.e., SSPSR is still shifting out a
data byte), the WCOL bit is set and the contents of the
buffer are unchanged (the write doesn’t occur) after
2 T
within 2 T
updated. This may result in a corrupted transfer.
DS39977C-page 328
CY
Acknowledge,
after the SSPBUF write. If SSPBUF is rewritten
CY
I
TRANSMISSION
(Figure
2
, the WCOL bit is set and SSPBUF is
C™ MASTER MODE
BF Status Flag
WCOL Status Flag
21-23).
the Acknowledge
BRG
BRG
). Data should be valid
. The data on the SDA
Status bit,
Preliminary
The user should verify that the WCOL bit is clear after
each write to SSPBUF to ensure the transfer is correct.
In all cases, WCOL must be cleared in software.
21.4.10.3
In Transmit mode, the ACKSTAT bit (SSPCON2<6>) is
cleared when the slave has sent an Acknowledge
(ACK = 0 ) and is set when the slave does not Acknowl-
edge (ACK = 1 ). A slave sends an Acknowledge when
it has recognized its address (including a general call),
or when the slave has properly received its data.
21.4.11
Master mode reception is enabled by programming the
Receive Enable bit, RCEN (SSPCON2<3>).
The Baud Rate Generator begins counting, and on
each rollover, the state of the SCL pin changes
(high-to-low/low-to-high) and data is shifted into the
SSPSR. After the falling edge of the eighth clock, the
receive enable flag is automatically cleared, the con-
tents of the SSPSR are loaded into the SSPBUF, the
BF flag bit is set, the SSPIF flag bit is set and the Baud
Rate Generator is suspended from counting, holding
SCL low. The MSSP is now in Idle state awaiting the
next command. When the buffer is read by the CPU,
the BF flag bit is automatically cleared. The user can
then send an Acknowledge bit at the end of reception
by setting the Acknowledge Sequence Enable bit,
ACKEN (SSPCON2<4>).
21.4.11.1
In receive operation, the BF bit is set when an address
or data byte is loaded into SSPBUF from SSPSR. It is
cleared when the SSPBUF register is read.
21.4.11.2
In receive operation, the SSPOV bit is set when 8 bits
are received into the SSPSR and the BF flag bit is
already set from a previous reception.
21.4.11.3
If the user writes the SSPBUF when a receive is
already in progress (i.e., SSPSR is still shifting in a data
byte), the WCOL bit is set and the contents of the buffer
are unchanged (the write doesn’t occur).
Note:
I
The MSSP module must be in an inactive
state before the RCEN bit is set or the
RCEN bit will be disregarded.
2
ACKSTAT Status Flag
C™ MASTER MODE RECEPTION
BF Status Flag
SSPOV Status Flag
WCOL Status Flag
2011 Microchip Technology Inc.
Related parts for PIC18F46K80-I/P
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PIC18F-LF1XK50](/images/no-image3.png)
Part Number:
Description:
20-Pin USB Flash Microcontrollers
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![PIC18F6393T-I/PT](/photos/6/81/68123/c04-066_pf_tmb.jpg)
Part Number:
Description:
PIC18F With 128-segment LCD Driver And 12-bit ADC, 8KB Flash, 768B RAM, CCP, MSS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F6493T-I/PT](/photos/6/81/68123/c04-066_pf_tmb.jpg)
Part Number:
Description:
PIC18F With 128-segment LCD Driver And 12-bit ADC, 16KB Flash, 768B RAM, CCP, MS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F8393T-I/PT](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
PIC18F With 192-segment LCD Driver And 12-bit ADC, 8KB Flash, 768B RAM, CCP, MSS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F8493T-I/PT](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
PIC18F With 192-segment LCD Driver And 12-bit ADC, 16KB Flash, 768B RAM, CCP, MS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F6585-I/L](/photos/16/12/161282/68-plcc-large-300dpi-lyrd_tmb.jpg)
Part Number:
Description:
Microcontrollers (MCU) 48KB 3328 RAM 52 I/O
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F6680-I/L](/photos/16/12/161282/68-plcc-large-300dpi-lyrd_tmb.jpg)
Part Number:
Description:
Microcontrollers (MCU) 64KB 3328 RAM 52 I/O
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90T-I/MR](/photos/16/3/160368/qfn64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm T/R
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90T-I/PT](/photos/16/3/160367/tqfp-64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm T/R
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F87K90T-I/PT](/photos/40/31/403173/tqfp-80_tmb.jpg)
Part Number:
Description:
128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm T/
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90-I/MR](/photos/16/3/160368/qfn64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm TUBE
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90-I/PT](/photos/16/3/160367/tqfp-64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm TRAY
Manufacturer:
Microchip Technology
![PIC18F87K90-I/PT](/photos/40/31/403173/tqfp-80_tmb.jpg)
Part Number:
Description:
128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm TR
Manufacturer:
Microchip Technology