WM8310GEB/V Wolfson Microelectronics, WM8310GEB/V Datasheet - Page 32

• Manufacturer Part Number: WM8310GEB/V
• Description: POWER MANAGEMENT SUBSYSTEM, 169BGA
• Manufacturer: Wolfson Microelectronics

Specifications of WM8310GEB/V

• Supply Voltage: 7V
• No. Of Step-down Dc - Dc Converters: 4
• No. Of Ldo Regulators: 11
• Digital Ic Case Style: BGA
• No. Of Pins: 169
• No. Of Regulated Outputs: 13
• Operating Temperature Range: -40°C To
• Rohs Compliant: Yes
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

WM8310
Pre-Production
Figure 5 Example Control Sequence for ‘ON’ State Transition
The possible ‘ON’ events that may trigger the ON sequence are listed in Table 3. The ON sequence
is only permitted when the supply voltage SYSVDD exceeds a programmable threshold SYSOK. See
Section 24 for details of SYSVDD voltage monitoring.
The OFF sequence is the reverse of the ON sequence. Each DC-DC Converter, LDO Regulator or
GPIO output that is associated with a timeslot in the ON sequence is switched off in the reverse
sequence following an ‘OFF’ event. If CLKOUT is assigned to a timeslot in the ON sequence, then
this is disabled in the reverse (OFF) sequence also.
The possible ‘OFF’ events are listed in Table 3. Note that it is possible to modify the OFF sequence
by writing to the associated registers in the ON power state if required; this allows the OFF sequence
to be independent of the ON sequence.
The SLEEP sequence is the transition from ON to SLEEP power states. Each LDO and each DC-DC
Converter (except DC-DC4) may be associated with any one of the available timeslots in the SLEEP
sequence. This determines the time, within the sequence, at which that DC Converter or LDO will be
disabled following a ‘SLEEP’ event.
The clock output (CLKOUT) and GPIO pins configured as External Power Enable (EPE) outputs can
also be associated with any one of the available timeslots in the SLEEP sequence. The possible
‘SLEEP’ events are listed in Table 3.
The WAKE sequence is the reverse of the SLEEP sequence. Each DC-DC Converter, LDO
Regulator or GPIO output that is associated with a timeslot in the SLEEP sequence is switched on in
the reverse sequence following a ‘WAKE’ event. If CLKOUT is assigned to a timeslot in the SLEEP
sequence, then this is disabled in the reverse (WAKE) sequence also.
The possible ‘WAKE’ events are listed in Table 3. Note that it is possible to modify the WAKE
sequence by writing to the associated registers in the SLEEP power state if required; this allows the
WAKE sequence to be independent of the SLEEP sequence.
Any DC-DC Converter or LDO that is not associated with one of the 5 timeslots in the ON sequence
may, instead, be configured to be hardware controlled via a GPIO pin configured as one of the
Hardware Enable inputs. See Section 21 for details of the GPIO functions. Any DC-DC Converter or
LDO that is not under Hardware control may be enabled or disabled under Software control in the ON
state, regardless of whether it is associated with any timeslot in the ON sequence.
When a valid OFF event occurs, any DC-DC Converter or LDO which is not allocated a timeslot in
the ON sequence is disabled immediately. This includes any DC-DC Converter or LDO which is
under GPIO (Hardware Enable) control. The only exception is LDO11 which may, optionally, be
configured to be enabled in the OFF state.
The WM8310 monitors the DC-DC Converters and LDOs during the ON sequence to ensure that the
required circuits have powered up successfully before proceeding to the next timeslot. The nominal
timeslot durations are extended if necessary in order to wait for the selected DC-DC Converters or
PP, December 2009, Rev 3.0
w
32