MT48LC16M8A2P-75L Micron Technology Inc, MT48LC16M8A2P-75L Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT48LC16M8A2P-75L
Manufacturer Part Number
MT48LC16M8A2P-75L
Description
Manufacturer
Micron Technology Inc
Type
SDRAMr
Datasheet
1.MT48LC16M8A2P-75L.pdf
(74 pages)
Specifications of MT48LC16M8A2P-75L
Organization
16Mx8
Density
128Mb
Address Bus
14b
Access Time (max)
6/5.4ns
Maximum Clock Rate
133MHz
Operating Supply Voltage (typ)
3.3V
Package Type
TSOP-II
Operating Temp Range
0C to 70C
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
3V
Supply Current
150mA
Pin Count
54
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / Rohs Status
Compliant
Pin/Ball Descriptions
Table 4:
PDF: 09005aef8091e66d/Source: 09005aef8091e625
128MSDRAM_2.fm - Rev. N 1/09 EN
54-Pin TSOP
23–26, 29–
16, 17, 18
34, 22, 35
15, 39
20, 21
38
37
19
39
Pin/Ball Descriptions
J7, J3, J2, H3,
H2, H1, G3,
H7, H8, J8,
F9, F7, F8
54-Ball
VFBGA
G7, G8
H9, G2
E8, F1
G9
F2
F3
–
M2, N8, M1
P1, N2, N1,
N7, P8, P7,
R8, R1, P2,
J7, J8, K7
M8, M7
60-Ball
FBGA
K2
L2
L8
J2
–
BA0, BA1
Symbol
A0–A11
DQML,
DQMH
x4, x8:
CAS#,
DQM
WE#,
RAS#
x16:
CLK
CKE
CS#
Input
Input
Input
Input
Input
Input
Input
Type
13
Description
Clock: CLK is driven by the system clock. All SDRAM input
signals are sampled on the positive edge of CLK. CLK also
increments the internal burst counter and controls the
output registers.
Clock enable: CKE activates (HIGH) and deactivates (LOW)
the CLK signal. Deactivating the clock provides
PRECHARGE power-down and SELF REFRESH operation
(all banks idle), ACTIVE power-down (row active in any
bank), or CLOCK SUSPEND operation (burst/access in
progress). CKE is synchronous except after the device
enters power-down and self refresh modes, where CKE
becomes asynchronous until after exiting the same mode.
The input buffers, including CLK, are disabled during
power-down and self refresh modes, providing low
standby power. CKE may be tied HIGH.
Chip select: CS# enables (registered LOW) and disables
(registered HIGH) the command decoder. All commands
are masked when CS# is registered HIGH, but READ/WRITE
bursts already in progress will continue and DQM
operation will retain its DQ mask capability while CS# is
HIGH. CS# provides for external bank selection on systems
with multiple banks. CS# is considered part of the
command code.
Command inputs: WE#, CAS#, and RAS# (along with CS#)
define the command being entered.
Input/Output mask: DQM is an input mask signal for write
accesses and an output enable signal for read accesses.
Input data is masked when DQM is sampled HIGH during
a WRITE cycle. The output buffers are placed in a High-Z
state (2-clock latency) when DQM is sampled HIGH during
a READ cycle. On the x4 and x8, DQML (pin 15) is a NC and
DQMH is DQM. On the x16, DQML corresponds to DQ0–
DQ7, and DQMH corresponds to DQ8–DQ15. DQML and
DQMH are considered same state when referenced as
DQM.
Bank address inputs: BA0 and BA1 define to which bank
the ACTIVE, READ, WRITE, or PRECHARGE command is
being applied.
Address inputs: A0–A11 are sampled during the ACTIVE
command (row-address A0–A11) and READ/WRITE
command (column-address A0–A9, A11 [x4]; A0–A9 [x8];
A0–A8 [x16]; with A10 defining auto precharge) to select
one location out of the memory array in the respective
bank. A10 is sampled during a precharge command to
determine whether all banks are to be precharged (A10
[HIGH]) or bank selected by BA0, BA1 (A10 [LOW]). The
address inputs also provide the op-code during a LOAD
MODE REGISTER (LMR) command.
Micron Technology, Inc., reserves the right to change products or specifications without notice.
128Mb: x4, x8, x16 SDRAM
Pin/Ball Descriptions
©1999 Micron Technology, Inc. All rights reserved.