MCP23016-I/SP Microchip Technology, MCP23016-I/SP Datasheet - Page 12

• Manufacturer Part Number: MCP23016-I/SP
• Description: IC I/O EXPANDER I2C 16B 28SDIP
• Manufacturer: Microchip Technology

Specifications of MCP23016-I/SP

• Package / Case: 28-DIP (0.300", 7.62mm)
• Interface: I²C
• Number Of I /o: 16
• Interrupt Output: Yes
• Frequency - Clock: 400kHz
• Voltage - Supply: 2 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Includes: POR
• Logic Family: MCP23016
• Propagation Delay Time: 50 ns
• Operating Supply Voltage: 2 V to 5.5 V
• Power Dissipation: 1 W
• Operating Temperature Range: - 40 C to + 85 C
• Input Voltage: 4.5 V to 5.5 V
• Logic Type: I/O Expander
• Maximum Clock Frequency: 400 KHz
• Maximum Operating Frequency: 3.4 MHz
• Mounting Style: Through Hole
• Output Current: 25 mA
• Output Voltage: 4.5 V
• Chip Configuration: 16 Bit
• Bus Frequency: 400kHz
• Ic Interface Type: I2C
• No. Of I/o's: 16
• Supply Voltage Range: 2V To 5.5V
• Digital Ic Case Style: DIP
• No. Of Pins: 28
• Ic Function: I/O Expander
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

MCP23016
1.8
The
transfers data between the I
1.9
The MCP23016 asserts the open-drain interrupt output
(INT) low when one of the port pins changes state. Only
those pins that are configured as an input can cause an
interrupt. Pins defined as an output have no effect on
INT. The interrupt will remain active until a read from
either the port (GPn) on which the interrupt occurred or
the INTCAPn register is performed. If the input returns
to its previous state before a read operation, it will reset
the interrupt and the INT pin output will tri-state. Each
8-bit port is read separately, so reading GP0 or
INTCAP0 will not clear the interrupt generated by GP1
or INTCAP1, and vice versa.
Input change activity on each port will generate an
interrupt and the value of the particular port will be
captured and copied into INTCAP0/INTCAP1. The
INTCAPn registers are only updated when an interrupt
occurs on INT. These values will stay unchanged until
the user clears the interrupt by reading the port or the
INTCAPn register.
If the input port value changes back to normal before a
user-read, the INT output will be reset. However, the
INTCAP0/INTCAP1 will still contain the value of the
port at the interrupt change. If the port value changes
again, it will re-activate the interrupt and the new value
will be captured.
The first interrupt on change event following an
interrupt RESET will result in a capture event. Any fur-
ther change event that occurs before the interrupt is
reset will not result in a capture event.
DS20090C-page 12
Serializer/Deserializer
Serializer/Deserializer
Interrupt Logic
2
C bus and GPIO.
block
converts
and
1.9.1
The IARES bit controls the resolution for detecting an
interrupt-on-change event. If this bit is ‘0’ (default), the
maximum time for detecting a change of event is high,
which results in lower standby current. If this bit is ‘1’, it
takes less time for scanning the activity on the port and
results in higher standby current.
FIGURE 1-2:
GPx
INT
Port value
is captured
and written to
INTCAPn
INTERRUPT EVENT DETECTION
PORT X
Read GPx
or INTCAPn
READING PORTX AFTER
INTERRUPT EVENT
© 2007 Microchip Technology Inc.
PORT X
Port value
is captured
and written to
INTCAPn