A2F200M3F-FGG484 Actel, A2F200M3F-FGG484 Datasheet - Page 52

• Manufacturer Part Number: A2F200M3F-FGG484
• Description: ACLA2F200M3F-FGG484 SMART FUSION MIX SIG
• Manufacturer: Actel

SmartFusion DC and Switching Characteristics
Table 2-58 • Minimum and Maximum DC Input and Output Levels
Figure 2-11 • AC Loading
Table 2-59 • AC Waveforms, Measuring Points, and Capacitive Loads
Table 2-60 • 3.3 V PCI
Table 2-61 • 3.3 V PCI-X
2- 40
3.3 V PCI/PCI-X
Drive Strength
Per PCI specification
Notes:
1. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
2. Currents are measured at 85°C junction temperature.
Input Low (V)
0
*
Speed Grade
–1
Note:
Speed Grade
–1
Note:
Measuring point = V
Test Point
Datapath
For specific junction temperature and voltage supply levels, refer to
For specific junction temperature and voltage supply levels, refer to
Worst Commercial-Case Conditions: T
Worst-Case VCCxxxxIOBx = 3.0 V
Applicable to FPGA I/O Banks
Worst Commercial-Case Conditions: T
Worst-Case VCCxxxxIOBx = 3.0 V
Applicable to Standard Plus I/O Banks
3.3 V PCI, 3.3 V PCI-X
Peripheral Component Interface for 3.3 V standard specifies support for 33 MHz and 66 MHz PCI Bus
applications.
AC loadings are defined per the PCI/PCI-X specifications for the datapath; Actel loadings for enable path
characterization are described in
AC loadings are defined per PCI/PCI-X specifications for the datapath; Actel loading for tristate is
described in
Timing Characteristics
R = 25
t
t
Input High (V)
DOUT
0.50
DOUT
0.50
trip.
3.3
Min.
See
Table
V
2.06
2.06
t
t
R to VCCXXXXIOBX for t
R to GND for t
DP
DP
VIL
Table 2-21 on page 2-26
2-59.
Max.
V
0.03
0.03
t
t
DIN
DIN
0.285 * VCCxxxxIOBx for t
0.615 * VCCxxxxIOBx for t
DP
Min.
Measuring Point* (V)
(R)
V
0.66
0.64
t
t
PY
PY
Figure
VIH
Max.
DP
t
t
V
EOUT
0.32
EOUT
0.32
(F)
2-11.
J
J
Enable Path
= 85°C, Worst-Case VCC = 1.425 V,
= 85°C, Worst-Case VCC = 1.425 V,
for a complete table of trip points.
Test Point
Per PCI curves
R e visio n 3
Max.
VOL
2.09
2.09
V
t
t
ZL
ZL
R = 1 k
DP(R)
DP(F)
VOH
Min.
1.50
1.50
V
t
t
ZH
ZH
Table 2-7 on page 2-9
Table 2-7 on page 2-9
mA mA
I
OL
10 pF for t
R to VCCXXXXIOBX for t
R to GND for t
5 pF for t
2.46
2.46
V
t
t
LZ
LZ
I
REF
OH
(typ.) (V)
–
HZ
ZH
2.75
2.75
t
t
Max.
mA
HZ
HZ
I
/ t
OSL
/ t
HZ
LZ
ZHS
1
/ t
/ t
ZH
3.81
3.81
t
t
ZL
ZLS
ZLS
/ t
for derating values.
for derating values.
/ t
ZHS
Max.
ZLS
I
mA
LZ
OSH
/ t
C
t
3.21
t
3.21
1
ZL
LOAD
ZHS
ZHS
/ t
10
ZLS
µA
15
I
(pF)
IL
Units
Units
2
ns
ns
µA
I
15
IH
2