MB91F376G Fujitsu Components, MB91F376G Datasheet - Page 212

• Manufacturer Part Number: MB91F376G
• Manufacturer: Fujitsu Components

Specifications of MB91F376G

• Lead Free Status / Rohs Status: Not Compliant

212
MB91360G Series
■ ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
*1 : Making full use of the allowed static DC correct into digital I/O will lead to lower values for V
*2 : • Applicable to pins : D0 to D31, A0 to A20, CS0X to CS6X, RDY, BGRNTX, BRQ, RDX, WR0X to WR3X, AS,
Digital supply voltage
External interface supply
Stepper motor control supply voltage
Storage temperature
Power consumption
Digital input voltage
Analog input voltage
Analog supply voltage
Analog reference voltage
Static DC current into digital I/O
Static total DC current into digital I/O
• Use within recommended operating conditions.
• Use at DC voltage (current) .
• The +B signal should always be applied with a limiting resistance placed between the +B signal and the
• The value of the limiting resistance should be set so that when the +B signal is applied the input current to
• Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
• Note that if a +B signal is input when the microcontroller current is off (not fixed at 0 V) , the power supply is
• Note that if the +B input is applied during power-on, the power supply is provided from the pins and the resulting
• Care must be taken not to leave the +B input pin open.
• Note that analog system input/output pins other than the A/D input pins (LCD drive pins, comparator input
microcontroller.
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
potential may pass through the protective diode and increase the potential at the V
other devices.
provided from the pins, so that incomplete operation may result.
supply voltage may not be sufficient to operate the power-on reset.
pins, etc.) cannot accept +B signal input.
Parameter
ALE, CLK, DREQ0, DACK0, DEOP0, INT0 to INT7, SGO, SGA, SDA, SCL, SOT0, SIN0,
SCK0, OCPA0 to OCPA3, TX0, TX1, RX0, RX1, SOT3, SOT4, SIN3, SIN4,
SCK3, SCK4, LED0 to LED7 (MB91F362GB only) , IN0 to IN3 (MB91F362GB only) ,
OUT0 to OUT3 (MB91F362GB only) , OCPA4 to OCPA7 (MB91F362GB only) ,
SOT1, SOT2 (MB91F362GB only) , SIH1, SIH2 (MB91F362GB only) ,
SCK1, SCK2 (MB91F362GB only) , PWM1P0 to PWM1P3 (MB91F362GB only) ,
PWM1M0 to PWM1M3 (MB91F362GB only) , PWM2P0 to PWM2P3 (MB91F362GB only) ,
PWM2M0 to PWM2M3 (MB91F362GB only)
V
DD
HV
AV
V
Σ
Symbol
35-V
V
REFH/L
⏐
DD
DD
Tstg
CC
I
P
V
I/ODC
I
V
I/ODC
TOT
IDIG
-V
-HV
-AV
IA
SS
-
V
SS
⏐
SSA
SS
SS
−0.3*
−0.3
−0.3
−0.3
−0.3
−0.3
−0.3
−2.0
Min
−55
⎯
⎯
1
Rating
+125
Max
+6.0
+6.0
+6.5
+5.8
+5.8
+5.8
+5.8
+2.0
20
*3
Unit
mA
mA
W
°C
V
V
V
V
V
V
V
CC
T
V
AV
AV
AV
ΣI
*2
*4
pin, and this may affect
A
SS
I/ODC
= +25°C
SS
SS
SS
= 0 V, V
= 0 V, AV
= 0 V
= 0 V
Condition
< I
IDIG
SRUN
Min.
DD
, *2
(Continued)
= 5 V
CC
= 5 V