P89LV51RD2BBC NXP Semiconductors, P89LV51RD2BBC Datasheet - Page 36

• Manufacturer Part Number: P89LV51RD2BBC
• Description: MCU 8-Bit 89LV 80C51 CISC 64KB Flash 3.3V 44-Pin TQFP Tray
• Manufacturer: NXP Semiconductors

Specifications of P89LV51RD2BBC

• Package: 44TQFP
• Device Core: 80C51
• Family Name: 89LV
• Maximum Speed: 40 MHz
• Ram Size: 1 KB
• Program Memory Size: 64 KB
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 8 Bit
• Program Memory Type: Flash
• Number Of Programmable I/os: 32
• Interface Type: SPI/UART
• Operating Temperature: 0 to 70 °C
• Number Of Timers: 3

NXP Semiconductors
P89LV51RB2_RC2_RD2_5
Product data sheet
Fig 14. Timer 2 in Baud Rate Generator mode
OSC
T2 pin
TCLK = 1, Timer 2 is used as the UART transmit baud rate generator. RCLK has the same
effect for the UART receive baud rate. With these two bits, the serial port can have
different receive and transmit baud rates – Timer 1 or Timer 2.
Figure 14
The baud rate generation mode is like the auto-reload mode, when a rollover in TH2
causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2H and
RCAP2L, which are preset by software.
The baud rates in modes 1 and 3 are determined by Timer 2’s overflow rate given below:
The timer can be configured for either ‘timer’ or ‘counter’ operation. In many applications,
it is configured for ‘timer' operation (C/T2 = 0). Timer operation is different for Timer 2
when it is being used as a baud rate generator.
Usually, as a timer it would increment every machine cycle (i.e.,
frequency). As a baud rate generator, it increments at the oscillator frequency. Thus the
baud rate formula is as follows:
Where: (RCAP2H, RCAP2L) = the content of RCAP2H and RCAP2L taken as a 16-bit
unsigned integer.
The Timer 2 as a baud rate generator mode is valid only if RCLK and/or TCLK =
T2CON register. Note that a rollover in TH2 does not set TF2, and will not generate an
interrupt. Thus, the Timer 2 interrupt does not have to be disabled when Timer 2 is in the
baud rate generator mode. Also if the EXEN2 (T2 external enable flag) is set, a 1-to-0
transition in T2EX (Timer/counter 2 trigger input) will set EXF2 (T2 external flag) but will
T2EX pin
----------------------------------------------------------------------------------------------- -
16
Modes 1 and 3 baud rates = Timer 2 Overflow Rate / 16
Modes 1 and 3 baud rates =
2
65536 RCAP2H RCAP2L
Oscillator Frequency
transition
detector
shows Timer 2 in baud rate generator mode.
–
C/T2 = 0
C/T2 = 1
EXEN2
Rev. 05 — 15 December 2009
control
TR2
control
EXF2
RCAP2L RCAP2H
(8-bits)
timer 2
interrupt
P89LV51RB2/RC2/RD2
TL2
(8-bits)
8-bit microcontrollers with 80C51 core
TH2
reload
TX/RX baud rate
1
002aaa526
6
the oscillator
© NXP B.V. 2009. All rights reserved.
1
in
36 of 76
(3)