PIC18F4585-H/P Microchip Technology, PIC18F4585-H/P Datasheet - Page 47

• Manufacturer Part Number: PIC18F4585-H/P
• Description: IC MCU 8BIT 48KB FLASH 40PDIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4585-H/P

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 48KB (24K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.25K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.5
PIC18F2585/2680/4585/4680
three separate on-chip timers that help regulate the
Power-on Reset process. Their main function is to
ensure that the device clock is stable before code is
executed. These timers are:
• Power-up Timer (PWRT)
• Oscillator Start-up Timer (OST)
• PLL Lock Time-out
4.5.1
The Power-up Timer (PWRT) of PIC18F2585/2680/
4585/4680 devices is an 11-bit counter which uses the
INTRC source as the clock input. This yields an
approximate time interval of 2048 x 32 μs = 65.6 ms.
While the PWRT is counting, the device is held in
Reset.
The power-up time delay depends on the INTRC clock
and will vary from chip to chip due to temperature and
process variation. See DC parameter 33 for details.
The PWRT is enabled by clearing the PWRTEN
Configuration bit.
4.5.2
The Oscillator Start-up Timer (OST) provides a 1024
oscillator cycle (from OSC1 input) delay after the
PWRT delay is over (parameter 33). This ensures that
the crystal oscillator or resonator has started and
stabilized.
The OST time-out is invoked only for XT, LP, HS and
HSPLL modes and only on Power-on Reset or on exit
from most power managed modes.
TABLE 4-2:
© 2007 Microchip Technology Inc.
HSPLL
HS, XT, LP
EC, ECIO
RC, RCIO
INTIO1, INTIO2
Note 1:
Configuration
Oscillator
2:
Device Reset Timers
66 ms (65.5 ms) is the nominal Power-up Timer (PWRT) delay.
2 ms is the nominal time required for the PLL to lock.
POWER-UP TIMER (PWRT)
OSCILLATOR START-UP TIMER
(OST)
TIME-OUT IN VARIOUS SITUATIONS
66 ms
66 ms
(1)
devices
PWRTEN = 0
+ 1024 T
(1)
66 ms
66 ms
66 ms
+ 1024 T
Power-up
(1)
(1)
(1)
OSC
incorporate
PIC18F2585/2680/4585/4680
+ 2 ms
OSC
Preliminary
(2)
(2)
and Brown-out
4.5.3
With the PLL enabled in its PLL mode, the time-out
sequence following a Power-on Reset is slightly
different from other oscillator modes. A separate timer
is used to provide a fixed time-out that is sufficient for
the PLL to lock to the main oscillator frequency. This
PLL lock time-out (T
the oscillator start-up time-out.
4.5.4
On power-up, the time-out sequence is as follows:
1.
2.
The total time-out will vary based on oscillator configu-
ration and the status of the PWRT. Figure 4-3,
Figure 4-4, Figure 4-5, Figure 4-6 and Figure 4-7 all
depict time-out sequences on power-up, with the
Power-up Timer enabled and the device operating in
HS Oscillator mode. Figures 4-3 through 4-6 also apply
to devices operating in XT or LP modes. For devices in
RC mode and with the PWRT disabled, on the other
hand, there will be no time-out at all.
Since the time-outs occur from the POR pulse, if MCLR
is kept low long enough, all time-outs will expire.
Bringing MCLR high will begin execution immediately
(Figure 4-5). This is useful for testing purposes or to
synchronize more than one PIC18FXXXX device
operating in parallel.
1024 T
PWRTEN = 1
After the POR pulse has cleared, PWRT
time-out is invoked (if enabled).
Then, the OST is activated.
1024 T
OSC
—
—
—
PLL LOCK TIME-OUT
TIME-OUT SEQUENCE
+ 2 ms
OSC
(2)
PLL
) is typically 2 ms and follows
Power Managed Mode
1024 T
1024 T
Exit from
DS39625C-page 45
OSC
—
—
—
+ 2 ms
OSC
(2)