LPC2420FBD208-S NXP Semiconductors, LPC2420FBD208-S Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
LPC2420FBD208-S
Manufacturer Part Number
LPC2420FBD208-S
Description
MCU 16-Bit/32-Bit LPC2000 ARM7TDMI-S RISC ROMLess 3.3V 208-Pin LQFP Tray
Manufacturer
NXP Semiconductors
Datasheet
1.LPC2460FBD208551.pdf
(79 pages)
Specifications of LPC2420FBD208-S
Package
208LQFP
Device Core
ARM7TDMI-S
Family Name
LPC2000
Maximum Speed
72 MHz
Ram Size
82 KB
Operating Supply Voltage
3.3 V
Data Bus Width
16|32 Bit
Program Memory Type
ROMLess
Number Of Programmable I/os
160
Interface Type
I2C/I2S/SPI/SSP/UART/USB
On-chip Adc
8-chx10-bit
On-chip Dac
1-chx10-bit
Operating Temperature
-40 to 85 °C
Number Of Timers
4
NXP Semiconductors
LPC2420_60_5
Preliminary data sheet
7.4.1 Interrupt sources
7.6.1 Features
7.5 Pin connect block
7.6 External memory controller
service routine can simply start dealing with that device. But if more than one request is
assigned to the FIQ class, the FIQ service routine can read a word from the VIC that
identifies which FIQ source(s) is (are) requesting an interrupt.
Vectored IRQs, which include all interrupt requests that are not classified as FIQs, have a
programmable interrupt priority. When more than one interrupt is assigned the same
priority and occur simultaneously, the one connected to the lowest numbered VIC channel
will be serviced first.
The VIC ORs the requests from all of the vectored IRQs to produce the IRQ signal to the
ARM processor. The IRQ service routine can start by reading a register from the VIC and
jumping to the address supplied by that register.
Each peripheral device has one interrupt line connected to the VIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any pin on port 0 and port 2 (total of 64 pins) regardless of the selected function, can be
programmed to generate an interrupt on a rising edge, a falling edge, or both. Such
interrupt request coming from port 0 and/or port 2 will be combined with the EINT3
interrupt requests.
The pin connect block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
The LPC2420/2460 EMC is an ARM PrimeCell MultiPort Memory Controller peripheral
offering support for asynchronous static memory devices such as RAM, ROM, and flash.
In addition, it can be used as an interface with off-chip memory-mapped devices and
peripherals. The EMC is an Advanced Microcontroller Bus Architecture (AMBA) compliant
peripheral.
•
•
•
•
•
•
•
Dynamic memory interface support including single data rate SDRAM.
Asynchronous static memory device support including RAM, ROM, and flash, with or
without asynchronous page mode.
Low transaction latency.
Read and write buffers to reduce latency and to improve performance.
8/16/32 data and 24 address lines wide static memory support.
16 bit and 32 bit wide chip select SDRAM memory support.
Static memory features include:
Rev. 05 — 24 February 2010
Flashless 16-bit/32-bit microcontroller
LPC2420/2460
© NXP B.V. 2010. All rights reserved.
28 of 79