DS3170+ Maxim Integrated Products, DS3170+ Datasheet - Page 106
![IC TXRX DS3/E3 100-CSBGA](/photos/6/94/69414/100-csbga_21-0153b_sml.jpg)
DS3170+
Manufacturer Part Number
DS3170+
Description
IC TXRX DS3/E3 100-CSBGA
Manufacturer
Maxim Integrated Products
Datasheet
1.DS3170.pdf
(230 pages)
Specifications of DS3170+
Function
Single-Chip Transceiver
Interface
DS3, E3
Number Of Circuits
1
Voltage - Supply
3.135 V ~ 3.465 V
Current - Supply
120mA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
100-LBGA
Includes
DS3 Framers, E3 Framers, HDLC Controller, On-Chip BERTs
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power (watts)
-
- Current page: 106 of 230
- Download datasheet (3Mb)
DS3170 DS3/E3 Single-Chip Transceiver
as the values for the first one. The third bipolar one is generated according to the normal AMI rules. When an EXZ
error is to be inserted, the Transmit Line Interface waits for the next occurrence of three (four) consecutive zeros on
the bipolar signal, and inhibits the insertion of a B3ZS (HDB3) signature. There must be at least one intervening
one between consecutive BPV or EXZ errors. A single BPV or EXZ error inserted must be detected as a single
BPV/EXZ error at the far-end, and not cause any other type of error to be detected. For example, if a BPV error is
inserted, the far-end should not also detect a data error. If a second error insertion request of a given type (BPV or
EXZ) is initiated before a previous request has been completed, the second request will be ignored.
The outgoing bipolar data stream consists of positive pulse data (TPOS) and negative pulse data (TNEG). TPOS
and TNEG are updated on the rising edge of TLCLK.
10.10.5 Receive Line Interface
The Receive Line Interface receives a bipolar signal. The incoming bipolar data line consists of positive pulse data
(RPOS), negative pulse data (RNEG), and clock (RLCLK) signals. RPOS and RNEG are sampled on the rising
edge of RLCLK. The incoming bipolar signal is checked for a Loss Of Signal (LOS) condition, and passed on to
B3ZS/HDB3 Decoder. An LOS condition is declared if both RPOS and RNEG do not have any transitions for 192
clock cycles. The LOS condition is terminated after 192 clock cycles without any EXZ errors. Note: When zero
suppression (B3ZS or HDB3) decoding is disabled, the LOS condition is cleared, and cannot be detected.
10.10.6 B3ZS/HDB3 Decoder
The B3ZS/HDB3 Decoder receives a bipolar signal from the LIU (or the RPOS/RNEG pins). The incoming bipolar
signal is checked for a Loss of Signal (LOS) condition. An LOS condition is declared if both the positive pulse data
and negative pulse data signals do not have any transitions for 192 clock cycles. The LOS condition is terminated
after 192 clock cycles without any EXZ errors.
B3ZS/HDB3 Decoder performs EXZ detection, zero suppression decoding, BPV detection, and bipolar to unipolar
conversion.
EXZ detection checks the bipolar data stream for excessive zeros (EXZ) errors. In B3ZS mode, an EXZ error is
declared whenever there is an occurrence of 3 or more zeros. In HDB3 mode, an EXZ error is declared whenever
there is an occurrence of 4 or more zeros. EXZ errors are accumulated in the EXZ counter (LINE.REXZCR
register).
Zero-suppression decoding converts B3ZS or HDB3 encoded bipolar data into an AMI bipolar signal. In B3ZS
mode, the encoded bipolar signal is checked for a B3ZS signature. If a B3ZS signature is found, it is replaced with
three zeros. In HDB3 mode, the encoded bipolar signal is checked for an HDB3 signature. If an HDB3 signature is
found, it is replaced with four zeros. The format of both an HDB3 signature and a B3ZS signature is programmable.
When LINE.RCR.RZSF = 0, the decoder will search for a zero followed by a BPV in B3ZS mode, and in HDB3
mode it will search for two zeros followed by a BPV. If LINE.RCR.RZSF = 1, the same criteria is applied with an
additional requirement that the BPV must be the opposite polarity of the previous BPV. Please refer to
Figure
10-25
and
Figure
10-26. Zero suppression decoding is also programmable (on or off). Note: Immediately after a
reset or a LOS condition, the first B3ZS/HDB3 signature to be detected will not depend upon the polarity of any
BPV contained within the signature.
106 of 230
Related parts for DS3170+
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![MAX7528KCWP](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3261CCJ](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3263CAG](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX8809AETL+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX1535CETJ+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
![DS2741N+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
![MAX13450EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX13451EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX17497BATE+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
![MAX17502FATB+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
![MAX1978EVKIT](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
![MAX2606EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2608EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2831EVKIT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
![MAX4888CETI+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: