ATmega406 Atmel Corporation, ATmega406 Datasheet - Page 178

• Manufacturer Part Number: ATmega406
• Manufacturer: Atmel Corporation

Specifications of ATmega406

• Flash (kbytes): 40 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 1 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 18
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1.9
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -30 to 85
• I/o Supply Class: 4.0 to 25
• Operating Voltage (vcc): 4.0 to 25
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Pwm Channels: 2
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27. Boot Loader Support – Read-While-Write Self-Programming
27.1
27.2
27.2.1
27.2.2
178
Boot Loader Features
Application and Boot Loader Flash Sections
ATmega406
Application Section
BLS – Boot Loader Section
The Boot Loader Support provides a real Read-While-Write Self-Programming mechanism for
downloading and uploading program code by the MCU itself. This feature allows flexible applica-
tion software updates controlled by the MCU using a Flash-resident Boot Loader program. The
Boot Loader program can use any available data interface and associated protocol to read code
and write (program) that code into the Flash memory, or read the code from the program mem-
ory. The program code within the Boot Loader section has the capability to write into the entire
Flash, including the Boot Loader memory. The Boot Loader can thus even modify itself, and it
can also erase itself from the code if the feature is not needed anymore. The size of the Boot
Loader memory is configurable with fuses and the Boot Loader has two separate sets of Boot
Lock bits which can be set independently. This gives the user a unique flexibility to select differ-
ent levels of protection.
•
•
•
•
•
•
•
Note:
The Flash memory is organized in two main sections, the Application section and the Boot
Loader section (see
BOOTSZ Fuses as shown in
have different level of protection since they have different sets of Lock bits.
The Application section is the section of the Flash that is used for storing the application code.
The protection level for the Application section can be selected by the application Boot Lock bits
(Boot Lock bits 0), see
Boot Loader code since the SPM instruction is disabled when executed from the Application
section.
While the Application section is used for storing the application code, the The Boot Loader soft-
ware must be located in the BLS since the SPM instruction can initiate a programming when
executing from the BLS only. The SPM instruction can access the entire Flash, including the
BLS itself. The protection level for the Boot Loader section can be selected by the Boot Loader
Lock bits (Boot Lock bits 1), see
Read-While-Write Self-Programming
Flexible Boot Memory Size
High Security (Separate Boot Lock Bits for a Flexible Protection)
Separate Fuse to Select Reset Vector
Optimized Page
Code Efficient Algorithm
Efficient Read-Modify-Write Support
1. A page is a section in the Flash consisting of several bytes (see
used during programming. The page organization does not affect normal operation.
(1)
Size
Figure
Table 27-2 on page
Table 27-7 on page 193
27-2). The size of the different sections is configured by the
Table 27-3 on page
182. The Application section can never store any
182.
and
Figure
27-2. These two sections can
”Page Size” on page
2548E–AVR–07/06
198)