ATxmega16A4U Atmel Corporation, ATxmega16A4U Datasheet - Page 295

• Manufacturer Part Number: ATxmega16A4U
• Manufacturer: Atmel Corporation

Specifications of ATxmega16A4U

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 7
• Twi (i2c): 2
• Uart: 5
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 3.3
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 16
• Pwm Channels: 16
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

23.4
8331A–AVR–07/11
Frame Formats
on page
receiver and transmitter.
Table 23-2.
The leading edge is the first clock edge of a clock cycle. The trailing edge is the last clock edge
of a clock cycle.
Figure 23-4. UCPHA and INVEN data transfer timing diagrams.
Data transfer is frame based, where a serial frame consists of one character of data bits with
synchronization bits (start and stop bits) and an optional parity bit for error checking. Note that
this does not apply to master SPI operation (See
USART accepts all combinations of the following as valid frame formats:
A frame starts with the start bit, followed by all the data bits (least-significant bit first and most-
significant bit last). If enabled, the parity bit is inserted after the data bits, before the first stop bit.
One frame can be directly followed by a start bit and a new frame, or the communication line can
return to the idle (high) state.
frame formats. Bits inside brackets are optional.
• 1 start bit
• 5, 6, 7, 8, or 9 data bits
• no, even, or odd parity bit
• 1 or 2 stop bits
SPI Mode
0
1
2
3
295. Changing the setting of any of these bits during transmission will corrupt both the
Data setup (TXD)
Data sample (RXD)
XCK
XCK
Data setup (TXD)
Data sample (RXD)
INVEN and UCPHA functionality.
INVEN
0
0
1
1
UCPOL=0
Figure 23-5 on page 296
UCPHA
0
1
0
1
Leading Edge
Rising, sample
Rising, setup
Falling, sample
Falling, setup
Atmel AVR XMEGA AU
”SPI Frame Formats” on page
Data setup (TXD)
Data setup (TXD)
XCK
Data sample (RXD)
XCK
Data sample (RXD)
illustrates the possible combinations of
Trailing Edge
Falling, setup
Falling, sample
Rising, setup
Rising, sample
UCPOL=1
296). The
295