ATxmega16A4U Atmel Corporation, ATxmega16A4U Datasheet - Page 442

• Manufacturer Part Number: ATxmega16A4U
• Manufacturer: Atmel Corporation

Specifications of ATxmega16A4U

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 7
• Twi (i2c): 2
• Uart: 5
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 3.3
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 16
• Pwm Channels: 16
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

33.11.5.4
33.11.5.5
33.11.5.6
33.11.5.7
8331A–AVR–07/11
Write EEPROM Page
Erase & Write EEPROM Page
Read EEPROM
Erase EEPROM
The Write EEPROM Page command is used to write all locations that is loaded in the EEPROM
page buffer into one page in EEPROM. Only the locations that are loaded and tagged in the
EEPROM page buffer will be written.
1.
2.
3.
self-programming.
The BUSY flag in the NVM STATUS register will be set until the operation is finished.
The Erase & Write EEPROM Page command is used to first erase an EEPROM page and write
the EEPROM page buffer into that page in EEPROM, in one atomic operation.
1.
2.
3.
self-programming.
The BUSY flag in the NVM STATUS register will be set until the operation is finished.
The Erase EEPROM command is used to erase all the locations in all EEPROM pages that cor-
responds the loaded and tagged locations in the EEPROM page buffer.
1.
2.
self-programming.
The BUSY flag in the NVM STATUS register will be set until the operation is finished.
The Read EEPROM command is used to read one byte from the EEPROM,
1.
2.
3.
self-programming.
The data byte read will be available in the NVM DATA0.
Load the NVM CMD register with the Write EEPROM Page command.
Load the NVM ADDR register with the address for EEPROM page to write.
Set the CMDEX bit in NVM CTRLA register. This requires the timed CCP sequence during
Load the NVM CMD register with the Erase & Write EEPROM Page command.
Load the NVM ADDR register with the address for EEPROM page to write.
Set the CMDEX bit in NVM CTRLA register. This requires the timed CCP sequence during
Set up the NVM CMD register to Erase EPPROM command.
Set the CMDEX bit in NVM CTRLA register. This requires the timed CCP sequence during
Load the NVM CMD register with the Read EEPROM command.
Load the NVM ADDR register with the address to read.
Set the CMDEX bit in NVM CTRLA register. This requires the timed CCP sequence during
Atmel AVR XMEGA AU
442