SAM3N4A Atmel Corporation, SAM3N4A Datasheet - Page 397

• Manufacturer Part Number: SAM3N4A
• Manufacturer: Atmel Corporation

Specifications of SAM3N4A

• Flash (kbytes): 256 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 48 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Quadrature Decoder Channels: 2
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 2
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 24
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

26.6
11011A–ATARM–04-Oct-10
11011A–ATARM–04-Oct-10
I/O Lines Programming Example
The programing example as shown in
configuration.
Table 26-1.
• 4-bit output port on I/O lines 0 to 3, (should be written in a single write operation), open-drain,
• Four output signals on I/O lines 4 to 7 (to drive LEDs for example), driven high and low, no
• Four input signals on I/O lines 8 to 11 (to read push-button states for example), with pull-up
• Four input signals on I/O line 12 to 15 to read an external device status (polled, thus no input
• I/O lines 16 to 19 assigned to peripheral A functions with pull-up resistor
• I/O lines 20 to 23 assigned to peripheral B functions with pull-down resistor
• I/O line 24 to 27 assigned to peripheral C with Input Change Interrupt, no pull-up resistor and
• I/O line 28 to 31 assigned to peripheral D, no pull-up resistor and no pull-down resistor
with pull-up resistor
pull-up resistor, no pull-down resistor
resistors, glitch filters and input change interrupts
change interrupt), no pull-up resistor, no glitch filter
no pull-down resistor
PIO_ABCDSR1
PIO_ABCDSR2
PIO_PPDDR
PIO_PPDER
PIO_OWDR
PIO_MDDR
PIO_OWER
PIO_SODR
PIO_CODR
PIO_MDER
PIO_PUDR
PIO_PUER
PIO_ODR
PIO_IFER
PIO_IFDR
PIO_PDR
PIO_OER
PIO_PER
Register
PIO_IDR
PIO_IER
Programming Example
Table 26-1
Value to be Written
below is used to obtain the following
0x0FFF_ FFF0
0xFFFF_FF00
0xFFFF_F0FF
0x0FFF_FFFF
0xF0FF_F0FF
0xFFFF_FFF0
0xFF0F_FFFF
0x0000_FFFF
0xFFFF_0000
0xFFF0_00F0
0x000F_FF0F
0x0000_00FF
0x0000_0F00
0x0F00_0F00
0x0000_000F
0x00F0_0000
0xF0F0_0000
0xFF00_0000
0x0000_000F
0x0000_0000
SAM3N
SAM3N
397
397