SAM9263 Atmel Corporation, SAM9263 Datasheet - Page 130
SAM9263
Manufacturer Part Number
SAM9263
Description
Manufacturer
Atmel Corporation
Datasheets
1.M40800.pdf
(284 pages)
2.M40800.pdf
(153 pages)
3.SAM9260.pdf
(290 pages)
4.SAM9261.pdf
(248 pages)
5.SAM9263.pdf
(1109 pages)
6.SAM9263.pdf
(51 pages)
Specifications of SAM9263
Flash (kbytes)
0 Kbytes
Pin Count
324
Max. Operating Frequency
240 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
160
Ext Interrupts
160
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
1
Uart
4
Can
1
Ssc
2
Ethernet
1
Sd / Emmc
2
Graphic Lcd
Yes
Video Decoder
No
Camera Interface
Yes
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
96
Self Program Memory
NO
External Bus Interface
2
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Fpu
No
Mpu / Mmu
No / Yes
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- M40800 PDF datasheet
- M40800 PDF datasheet #2
- SAM9260 PDF datasheet #3
- SAM9261 PDF datasheet #4
- SAM9263 PDF datasheet #5
- SAM9263 PDF datasheet #6
- Current page: 130 of 284
- Download datasheet (2Mb)
Debug Interface
5-8
•
Entry into debug state on watchpoint
Watchpoints occur on data accesses. A watchpoint is always taken, but the core might
not enter debug state immediately. In all cases, the current instruction completes. If the
current instruction is a multi-word load or store, with an LDM or STM, many cycles can
elapse before the watchpoint is taken.
When a watchpoint occurs, the current instruction completes, and all changes to the core
state are made, load data is written into the destination registers and base write-back
occurs.
Watchpoints are similar to Data Aborts. The difference is that when a Data Abort
occurs, although the instruction completes, the processor prevents all subsequent
changes to the ARM7TDMI processor state. This action allows the abort handler to cure
the cause of the abort and the instruction to be re-executed.
If a watchpoint occurs when an exception is pending, the core enters debug state in the
same mode as the exception.
Entry into debug state on debug request
The ARM7TDMI processor can be forced into debug state on debug request in either of
the following ways:
•
•
The DBGRQ pin is an asynchronous input and is therefore synchronized by logic inside
the ARM7TDMI processor before it takes effect. Following synchronization, the core
normally enters debug state at the end of the current instruction. However, if the current
instruction is a busy-waiting access to a coprocessor, the instruction terminates and
ARM7TDMI processor enters debug state immediately. This is similar to the action of
nIRQ and nFIQ.
An exception occurs, causing the processor to flush the instruction pipeline and
cancel the breakpoint. In normal circumstances, on exiting from an exception, the
ARM7TDMI core branches back to the next instruction to be executed before the
exception occurred. In this case, the pipeline is refilled and the breakpoint is
reflagged.
through EmbeddedICE Logic programming (see Programming breakpoints on
page B-45 and Programming watchpoints on page B-47)
by asserting the DBGRQ pin.
Note
Copyright © 1994-2001. All rights reserved.
ARM DDI 0029G
Related parts for SAM9263
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: