SAM9263 Atmel Corporation, SAM9263 Datasheet - Page 266
SAM9263
Manufacturer Part Number
SAM9263
Description
Manufacturer
Atmel Corporation
Datasheets
1.M40800.pdf
(284 pages)
2.M40800.pdf
(153 pages)
3.SAM9260.pdf
(290 pages)
4.SAM9261.pdf
(248 pages)
5.SAM9263.pdf
(1109 pages)
6.SAM9263.pdf
(51 pages)
Specifications of SAM9263
Flash (kbytes)
0 Kbytes
Pin Count
324
Max. Operating Frequency
240 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
160
Ext Interrupts
160
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
1
Uart
4
Can
1
Ssc
2
Ethernet
1
Sd / Emmc
2
Graphic Lcd
Yes
Video Decoder
No
Camera Interface
Yes
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
96
Self Program Memory
NO
External Bus Interface
2
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Fpu
No
Mpu / Mmu
No / Yes
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- M40800 PDF datasheet
- M40800 PDF datasheet #2
- SAM9260 PDF datasheet #3
- SAM9261 PDF datasheet #4
- SAM9263 PDF datasheet #5
- SAM9263 PDF datasheet #6
- Current page: 266 of 284
- Download datasheet (2Mb)
Debug in Depth
B.15
B-48
The debug control register
The debug control register is 3 bits wide. Writing control bits occurs during a register
write access with the read/write bit HIGH. Reading control bits occurs during a register
read access with the read/write bit LOW.
Figure B-9 on page B-48 shows the function of each bit in this register.
If Bit 2, INTDIS, is asserted, the interrupt enable signal, IFEN of the core is forced
LOW. Therefore. all interrupts, IRQ and FIQ, are disabled during debugging,
DBGACK is HIGH, or if the INTDIS bit is asserted. The IFEN signal is driven as listed
in Table B-7 on page B-48.
Bits 1 and 0 enable the values on DBGRQ and DBGACK to be forced.
Figure B-11 on page B-51 shows that the value stored in bit 1 of the control register is
synchronized and then ORed with the external DBGRQ before being applied to the
processor. The output of this OR gate is the signal DBGRQI which is brought out
externally from the macrocell.
The synchronization between control bit 1 and DBGRQI is to assist in multiprocessor
environments. The synchronization latch only opens when the TAP controller state
machine is in the RUN-TEST-IDLE state. This enables an enter debug condition to be
set up in all the processors in the system while they are still running. When the condition
is set up in all the processors, it can then be applied to them simultaneously by entering
the RUN-TEST-IDLE state.
Copyright © 1994-2001. All rights reserved.
DBGACK
LOW
HIGH
x
Figure B-9 Debug control register format
INTDIS
2
Table B-7 Interrupt signal control
INTDIS
LOW
x
HIGH
DBGRQ
1
IFEN
HIGH
LOW
LOW
ARM DDI 0029G
DBGACK
Interrupts
Permitted
Inhibited
Inhibited
0
Related parts for SAM9263
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: