SAM9M10 Atmel Corporation, SAM9M10 Datasheet - Page 840
SAM9M10
Manufacturer Part Number
SAM9M10
Description
Manufacturer
Atmel Corporation
Datasheets
1.M40800.pdf
(284 pages)
2.SAM9261.pdf
(248 pages)
3.SAM9M10.pdf
(59 pages)
4.SAM9M10.pdf
(1398 pages)
Specifications of SAM9M10
Flash (kbytes)
0 Kbytes
Pin Count
324
Max. Operating Frequency
400 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
160
Ext Interrupts
160
Usb Transceiver
3
Usb Speed
Hi-Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
2
Uart
5
Lin
4
Ssc
2
Ethernet
1
Sd / Emmc
2
Graphic Lcd
Yes
Video Decoder
Yes
Camera Interface
Yes
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
440
Resistive Touch Screen
Yes
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
64
Self Program Memory
NO
External Bus Interface
2
Dram Memory
DDR2/LPDDR, SDRAM/LPSDR
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
0.9 to 1.1
Fpu
No
Mpu / Mmu
No / Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 840 of 1398
- Download datasheet (24Mb)
38.6.1
Name:
Address:
Access:
• DEV_ADDR: UDPHS Address
Read:
This field contains the default address (0) after power-up or UDPHS bus reset.
Write:
This field is written with the value set by a SET_ADDRESS request received by the device firmware.
• FADDR_EN: Function Address Enable
Read:
0 = Device is not in address state.
1 = Device is in address state.
Write:
0 = only the default function address is used (0).
1 = this bit is set by the device firmware after a successful status phase of a SET_ADDRESS transaction. When set, the
only address accepted by the UDPHS controller is the one stored in the UDPHS Address field. It will not be cleared after-
wards by the device firmware. It is cleared by hardware on hardware reset, or when UDPHS bus reset is received (see
above).
• EN_UDPHS: UDPHS Enable
Read:
0 = UDPHS is disabled.
1 = UDPHS is enabled.
Write:
0 = disable and reset the UDPHS controller. Switch the host to UTMI.
1 = enables the UDPHS controller. Switch the host to UTMI.
840
FADDR_EN
31
23
15
–
–
–
7
SAM9M10
UDPHS Control Register
30
22
14
UDPHS_CTRL
0xFFF78000
Read-write
–
–
–
6
29
21
13
–
–
–
5
28
20
12
–
–
–
4
PULLD_DIS
DEV_ADDR
27
19
11
–
–
3
REWAKEUP
26
18
10
–
–
2
DETACH
25
17
–
–
9
1
6355D–ATARM–7-Sep-11
EN_UDPHS
24
16
–
–
8
0
Related parts for SAM9M10
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: