SAM9M10 Atmel Corporation, SAM9M10 Datasheet - Page 926
SAM9M10
Manufacturer Part Number
SAM9M10
Description
Manufacturer
Atmel Corporation
Datasheets
1.M40800.pdf
(284 pages)
2.SAM9261.pdf
(248 pages)
3.SAM9M10.pdf
(59 pages)
4.SAM9M10.pdf
(1398 pages)
Specifications of SAM9M10
Flash (kbytes)
0 Kbytes
Pin Count
324
Max. Operating Frequency
400 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
160
Ext Interrupts
160
Usb Transceiver
3
Usb Speed
Hi-Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
2
Uart
5
Lin
4
Ssc
2
Ethernet
1
Sd / Emmc
2
Graphic Lcd
Yes
Video Decoder
Yes
Camera Interface
Yes
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
440
Resistive Touch Screen
Yes
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
64
Self Program Memory
NO
External Bus Interface
2
Dram Memory
DDR2/LPDDR, SDRAM/LPSDR
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
0.9 to 1.1
Fpu
No
Mpu / Mmu
No / Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 926 of 1398
- Download datasheet (24Mb)
Figure 40-2. Touch Screen Position Measurement
40.7.2
926
SAM9M10
Position Measurement Method
As shown in
bottom. Due to the linear resistance of the film, there is a voltage gradient from top to bottom.
When a contact is performed on the screen, the voltage propagates at the point the two surfaces
come into contact with the second film. If the input impedance on the right and left electrodes
sense is high enough, the film does not affect this voltage, despite its resistive nature.
For the horizontal direction, the same method is used, but by applying supply from left to right.
The range depends on the supply voltage and on the loss in the switches that connect to the top
and bottom electrodes.
In an ideal world (linear, with no loss through switches), the horizontal position is equal to:
The proposed implementation with on-chip power switches is shown in
measurement at the output of the switch compensates for the switches loss.
It is possible to correct for the switch loss by performing the operation:
This requires additional measurements, as shown in
Vertical Position Detection
X
X
M
P
VY
[VY
M
P
Y
/ VDD or VY
- VX
M
Figure
Y
P
M
] / [VX
Volt
VDD
40-2, to detect the position of a contact, a supply is first applied from top to
GND
P
P
X
M
/ VDD.
- VX
Contact
Pen
M
].
X
P
Horizontal Position Detection
Y
Y
M
P
Y
P
Figure
X
P
40-3.
Volt
VDD
GND
Figure
6355D–ATARM–7-Sep-11
40-3. The voltage
Related parts for SAM9M10
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: