SAM9M10 Atmel Corporation, SAM9M10 Datasheet - Page 841
SAM9M10
Manufacturer Part Number
SAM9M10
Description
Manufacturer
Atmel Corporation
Datasheets
1.M40800.pdf
(284 pages)
2.SAM9261.pdf
(248 pages)
3.SAM9M10.pdf
(59 pages)
4.SAM9M10.pdf
(1398 pages)
Specifications of SAM9M10
Flash (kbytes)
0 Kbytes
Pin Count
324
Max. Operating Frequency
400 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
160
Ext Interrupts
160
Usb Transceiver
3
Usb Speed
Hi-Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
2
Uart
5
Lin
4
Ssc
2
Ethernet
1
Sd / Emmc
2
Graphic Lcd
Yes
Video Decoder
Yes
Camera Interface
Yes
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
440
Resistive Touch Screen
Yes
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
64
Self Program Memory
NO
External Bus Interface
2
Dram Memory
DDR2/LPDDR, SDRAM/LPSDR
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
0.9 to 1.1
Fpu
No
Mpu / Mmu
No / Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 841 of 1398
- Download datasheet (24Mb)
• DETACH: Detach Command
Read:
0 = UDPHS is attached.
1 = UDPHS is detached, UTMI transceiver is suspended.
Write:
0 = pull up the DP line (attach command).
1 = simulate a detach on the UDPHS line and force the UTMI transceiver into suspend state (Suspend M = 0).
(See PULLD_DIS description below.)
•
Read:
0 = Remote Wake Up is disabled.
1 = Remote Wake Up is enabled.
Write:
0 = no effect.
1 = force an external interrupt on the UDPHS controller for Remote Wake UP purposes.
An Upstream Resume is sent only after the UDPHS bus has been in SUSPEND state for at least 5 ms.
This bit is automatically cleared by hardware at the end of the Upstream Resume.
• PULLD_DIS: Pull-Down Disable
When set, there is no pull-down on DP & DM. (DM Pull-Down = DP Pull-Down = 0).
Note: If the DETACH bit is also set, device DP & DM are left in high impedance state.
(See DETACH description above.)
6355D–ATARM–7-Sep-11
DETACH
0
0
1
1
REWAKEUP
: Send Remote Wake Up
PULLD_DIS
0
1
0
1
DP
Pull up
Pull up
Pull down
High impedance
state
DM
Pull down
High impedance
state
Pull down
High impedance
state
Condition
not recommended
VBUS present
No VBUS
VBUS present &
software disconnect
SAM9M10
841
Related parts for SAM9M10
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: