AD5781 Analog Devices, AD5781 Datasheet - Page 21
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD5781
Manufacturer Part Number
AD5781
Description
Manufacturer
Analog Devices
Datasheet
1.AD5781.pdf
(28 pages)
Specifications of AD5781
Resolution (bits)
18bit
Dac Update Rate
1MSPS
Dac Settling Time
1µs
Max Pos Supply (v)
+33V
Single-supply
No
Dac Type
Unbuffered Vout
Dac Input Format
Ser,SPI
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD5781ARUZ
Manufacturer:
AD
Quantity:
210
Part Number:
AD5781BRUZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD5781SRU-EP
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Data Sheet
Standalone Operation
The serial interface works with both a continuous and noncon-
tinuous serial clock. A continuous SCLK source can be used
only if SYNC is held low for the correct number of clock cycles.
In gated clock mode, a burst clock containing the exact number
of clock cycles must be used, and SYNC must be taken high
after the final clock to latch the data. The first falling edge of
SYNC starts the write cycle. Exactly 24 falling clock edges must
be applied to SCLK before SYNC is brought high again. If
SYNC is brought high before the 24
data written is invalid. If more than 24 falling SCLK edges are
applied before SYNC is brought high, the input data is also
invalid. The input shift register is updated on the rising edge of
SYNC . For another serial transfer to take place, SYNC must be
brought low again. After the end of the serial data transfer, data
is automatically transferred from the input shift register to the
addressed register. Once the write cycle is complete, the output
can be updated by taking LDAC low while SYNC is high.
Daisy-Chain Operation
For systems that contain several devices, the SDO pin can be
used to daisy chain several devices together. Daisy-chain mode
can be useful in system diagnostics and in reducing the number
of serial interface lines. The first falling edge of SYNC starts the
write cycle. SCLK is continuously applied to the input shift
register when SYNC is low. If more than 24 clock pulses are
applied, the data ripples out of the shift register and appears on
the SDO line. This data is clocked out on the rising edge of
SCLK and is valid on the falling edge. By connecting the SDO
of the first device to the SDIN input of the next device in the
chain, a multidevice interface is constructed. Each device in the
system requires 24 clock pulses. Therefore, the total number of
clock cycles must equal 24 × N, where N is the total number of
AD5781
devices is complete,
data in each device in the daisy chain and prevents any further
data from being clocked into the input shift register. The serial
clock can be a continuous or a gated clock.
A continuous SCLK source can be used only if SYNC is held
low for the correct number of clock cycles. In gated clock mode,
a burst clock containing the exact number of clock cycles must
be used, and SYNC must be taken high after the final clock to
latch the data.
In any one daisy-chain sequence, writes to the DAC register
should not be mixed with writes to any of the other registers.
All writes to the daisy-chained parts should be either writes to
the DAC registers or writes to the control, clearcode, or
software control register.
devices in the chain. When the serial transfer to all
SYNC is taken high. This latches the input
th
falling SCLK edge, the
Rev. C | Page 21 of 28
Readback
The contents of all the on-chip registers can be read back via
the SDO pin. Table 8 outlines how the registers are decoded.
After a register has been addressed for a read, the next 24 clock
cycles clock the data out on the SDO pin. The clocks must be
applied while SYNC is low. When SYNC is returned high, the
SDO pin is placed in tristate. For a read of a single register, the
NOP function can be used to clock out the data. Alternatively,
if more than one register is to be read, the data of the first
register to be addressed can be clocked out at the same time the
second register to be read is being addressed. The SDO pin
must be enabled to complete a readback operation. The SDO
pin is enabled by default.
HARDWARE CONTROL PINS
Load DAC Function ( LDAC )
After data has been transferred into the input register of the
DAC, there are two ways to update the DAC register and DAC
output. Depending on the status of both SYNC and LDAC , one
of two update modes is selected: synchronous DAC updating or
asynchronous DAC updating.
Synchronous DAC Update
In this mode, LDAC is held low while data is being clocked into
the input shift register. The DAC output is updated on the rising
edge of SYNC .
CONTROLLER
SERIAL CLOCK
CONTROL OUT
DATA IN
DATA OUT
*ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 51. Daisy-Chain Block Diagram
SDIN
SCLK
SYNC
SCLK
SYNC
SCLK
SYNC
AD5781*
AD5781*
AD5781*
SDIN
SDIN
SDO
SDO
SDO
AD5781