AD9747 Analog Devices, AD9747 Datasheet - Page 19

• Manufacturer Part Number: AD9747
• Description: Dual 16-Bit 250 MSPS Digital-to-Analog Converters
• Manufacturer: Analog Devices

Specifications of AD9747

• Resolution (bits): 16bit
• Dac Update Rate: 250MSPS
• Dac Settling Time: n/a
• Max Pos Supply (v): +3.47V
• Single-supply: No
• Dac Type: Current Out
• Dac Input Format: Par

internally by the serial port controller by decrementing from
the specified address. For LSB-first format, the specified address
is a beginning address or the least significant address in the
current cycle. Remaining register addresses for multiple byte
data transfers are generated internally by the serial port
controller by incrementing from the specified address.
MSB/LSB TRANSFERS
The serial port can support both MSB-first and LSB-first data
formats. This functionality is controlled by Register 0x00, Bit 6.
The default is Logic 0, which is MSB-first format.
When using MSB-first format (LSBFIRST = 0), the instruction
and data bit must be written from MSB to LSB. Multibyte data
transfers in MSB-first format start with an instruction byte that
includes the register address of the most significant data byte.
Subsequent data bytes are loaded into sequentially lower
address locations. In MSB-first mode, the serial port internal
address generator decrements for each byte of the multibyte
data transfer.
When using LSB-first format (LSBFIRST = 1), the instruction
and data bit must be written from LSB to MSB. Multibyte data
transfers in LSB-first format start with an instruction byte that
includes the register address of the least significant data byte.
Subsequent data bytes are loaded into sequentially higher
address locations. In LSB-first mode, the serial port internal
address generator increments for each byte of the multibyte
data transfer.
Use of a single-byte transfer when changing the serial port data
format is recommended to prevent unexpected device behavior.
SERIAL INTERFACE PORT PIN DESCRIPTIONS
Chip Select Bar (CSB)
Active low input starts and gates a communication cycle. It
allows more than one device to be used on the same serial
communication lines. CSB must stay low during the entire
communication cycle. Incomplete data transfers are aborted
anytime the CSB pin goes high. SDO and SDIO pins go to a
high impedance state when this input is high.
Serial Clock (SCLK)
The serial clock pin is used to synchronize data to and from the
device and to run the internal state machines. The maximum
frequency of SCLK is 40 MHz. All data input is registered on
the rising edge of SCLK. All data is driven out on the falling
edge of SCLK.
Serial Data I/O (SDIO)
Data is always written into the device on this pin. However,
SDIO can also function as a bidirectional data output line.
Rev. 0 | Page 19 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
The configuration of this pin is controlled by Register 0x00,
Bit 7. The default is Logic 0, which configures the SDIO pin
as unidirectional.
Serial Data Out (SDO)
Data is read from this pin for protocols that use separate lines
for transmitting and receiving data. The configuration of this
pin is controlled by Register 0x00, Bit 7. If this bit is set to a
Logic 1, the SDO pin does not output data and is set to a high
impedance state.
SCLK
SCLK
SDIO
SCLK
SCLK
SDIO
SDIO
SDO
SDO
SDIO
CSB
CSB
SDO
CSB
CSB
Figure 24. Serial Register Interface Timing—LSB First
R/W N1 N0
A0
Figure 25. Timing Diagram for SPI Register Write
Figure 26. Timing Diagram for SPI Register Read
Figure 23. Serial Register Interface—MSB First
INSTRUCTION CYCLE
INSTRUCTION CYCLE
INSTRUCTION BIT 7
A1 A2
t
t
S
DS
DATA BIT N
A4 A3
A3 A4
t
PWH
t
t
DH
DV
f
SCLK
A2 A1
N0 N1 R/W D0
–1
t
PWL
INSTRUCTION BIT 6
A0 D7 D6
DATA BIT N – 1
D0
D7 D6
0
0
DATA TRANSFER CYCLE
DATA TRANSFER CYCLE
D1
D1
N
N
0
0
D5
D5
D2
D2
N
N
0
0
D3
D4
D3
D4
0
N
0
N
D2
D2
D5
D5
0
0
N
N
D1
D6
D1
D6
0
0
N
N
D0
D0
D7
D7
0
0
N
N