P89LPC932A1 NXP Semiconductors, P89LPC932A1 Datasheet - Page 8

• Manufacturer Part Number: P89LPC932A1
• Description: The P89LPC932A1 is a single-chip microcontroller, available in low cost packages, basedon a high performance processor architecture that executes instructions in two to fourclocks, six times the rate of standard 80C51 devices
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 2.
P89LPC932A1_3
Product data sheet
Symbol
P0.4/ CIN1A/
KBI4
P0.5/
CMPREF/
KBI5
P0.6/CMP1/
KBI6
P0.7/T1/KBI7
P1.0 to P1.7
P1.0/TXD
P1.1/RXD
P1.2/T0/SCL
P1.3/INT0/
SDA
P1.4/INT1
Pin description
Pin
TSSOP28,
PLCC28,
DIP28
23
22
20
19
18
17
12
11
10
…continued
HVQFN28
19
18
16
15
14
13
8
7
6
Type Description
I/O
I
I
I/O
I
I
I/O
O
I
I/O
I/O
I
I/O, I
[1]
I/O
O
I/O
I
I/O
I/O
I/O
I/O
I
I/O
I
I
P0.4 — Port 0 bit 4.
CIN1A — Comparator 1 positive input A.
KBI4 — Keyboard input 4.
P0.5 — Port 0 bit 5.
CMPREF — Comparator reference (negative) input.
KBI5 — Keyboard input 5.
P0.6 — Port 0 bit 6.
CMP1 — Comparator 1 output.
KBI6 — Keyboard input 6.
P0.7 — Port 0 bit 7.
T1 — Timer/counter 1 external count input or overflow output.
KBI7 — Keyboard input 7.
Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type,
except for three pins as noted below. During reset Port 1 latches are
configured in the input only mode with the internal pull-up disabled. The
operation of the configurable Port 1 pins as inputs and outputs depends
upon the port configuration selected. Each of the configurable port pins
are programmed independently. Refer to
configurations”
P1.3 are open drain when used as outputs. P1.5 is input only.
All pins have Schmitt trigger inputs.
Port 1 also provides various special functions as described below:
P1.0 — Port 1 bit 0.
TXD — Transmitter output for the serial port.
P1.1 — Port 1 bit 1.
RXD — Receiver input for the serial port.
P1.2 — Port 1 bit 2 (open-drain when used as output).
T0 — Timer/counter 0 external count input or overflow output (open-drain
when used as output).
SCL — I
P1.3 — Port 1 bit 3 (open-drain when used as output).
INT0 — External interrupt 0 input.
SDA — I
P1.4 — Port 1 bit 4.
INT1 — External interrupt 1 input.
Rev. 03 — 12 March 2007
8-bit microcontroller with accelerated two-clock 80C51 core
2
2
C serial clock input/output.
C serial data input/output.
and
Table 8 “Static characteristics”
Section 7.13.1 “Port
P89LPC932A1
for details. P1.2 and
© NXP B.V. 2007. All rights reserved.
8 of 64