STM8TL53G4 STMicroelectronics, STM8TL53G4 Datasheet - Page 37

• Manufacturer Part Number: STM8TL53G4
• Description: 8-bit, ultra-low-power, touch-sensing MCUs with 16-Kbyte Flash and proximity detection
• Manufacturer: STMicroelectronics

Specifications of STM8TL53G4

• Operating Power Supply: 1.65 V to 3.6 V
• Temperature Range: –40 °C to 85 °C
• 4 Low Power Modes: Wait, Active-halt with AWU (1 μA), Active-halt with ProxSense™ (10 μA with scan every 200 ms),Halt (0.4 μA)
• Dynamic Power Consumption: 150 μA/MHz
• Fast Wakeup From Halt Mode: 4.7 μs
• Ultralow Leakage Per I/o: 50 nA

STM8TL53xx
9.3
9.3.1
Table 12.
1. I
2. When several inputs are submitted to a current injection, the maximum ΣI
Table 13.
Operating conditions
Subject to general operating conditions for V
General operating conditions
Table 14.
1. f
2. To calculate P
f
Symbol
MASTER
ΣI
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
there is no positive injection current, and the corresponding V
positive and negative injected currents (instantaneous values). These results are based on
characterization with ΣI
in this table and
Symbol
I
INJ(PIN)
MASTER
T
INJ(PIN)
Symbol
P
INJ(PIN)
STG
V
T
T
T
I
D
I
J
DD
VDD
VSS
I
A
J
(2)
IO
(1)
must never be exceeded. This is implicitly insured if V
= f
(1)
(1)
CPU.
Current characteristics
Thermal characteristics
General operating conditions
Storage temperature range
Maximum junction temperature
Dmax
Master clock frequency
Standard operating voltage
Power dissipation at T
°C for suffix 2 devices
Temperature range
Junction temperature range
Θ
Total current into V
Total current out of V
Output current sunk by any other I/O and control pin
Output current source by any I/Os and control pin
Injected current on any pin
Total injected current (sum of all I/O and control pins)
JA
(T
A
in table “Thermal characteristics”.
) use the formula given in thermal characteristics P
INJ(PIN)
IN
Parameter
>V
DD
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Doc ID 022344 Rev 1
Ratings
DD
A
= 85
SS
power line (source)
ground line (sink)
Ratings
(2)
1.65 V ≤ V
1.65 V ≤ V
−40 °C ≤ T
DD
Conditions
and T
UQFPN48
UQFPN28
-
IN
DD
DD
IN
A
A
maximum must always be respected.
.
≤ 85 °C
maximum is respected. If V
< 3.6 V
< 3.6 V
IN
Dmax
INJ(PIN)
<V
INJ(PIN)
(2)
SS
=(T
−65 to +150
1.65
. For true open-drain pads,
Min
−40
−40
is the absolute sum of the
Jmax
2
-
-
Electrical parameters
value. A positive
Min
150
−
T
A
)/
Max.
−25
±25
Θ
Max
±5
625
250
105
80
80
25
IN
3.6
16
85
JA
maximum
with T
Jmax
MHz
Unit
mW
Unit
Unit
°C
°C
° C
mA
V
37/62