STM8TL53G4 STMicroelectronics, STM8TL53G4 Datasheet - Page 44

• Manufacturer Part Number: STM8TL53G4
• Description: 8-bit, ultra-low-power, touch-sensing MCUs with 16-Kbyte Flash and proximity detection
• Manufacturer: STMicroelectronics

Specifications of STM8TL53G4

• Operating Power Supply: 1.65 V to 3.6 V
• Temperature Range: –40 °C to 85 °C
• 4 Low Power Modes: Wait, Active-halt with AWU (1 μA), Active-halt with ProxSense™ (10 μA with scan every 200 ms),Halt (0.4 μA)
• Dynamic Power Consumption: 150 μA/MHz
• Fast Wakeup From Halt Mode: 4.7 μs
• Ultralow Leakage Per I/o: 50 nA

Electrical parameters
9.3.7
Table 28.
1. V
2. Not applicable to PXS_RX and PXS_TX pins.
3. Data based on characterization results, not tested in production.
4. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization results, not tested.
5. The maximum value may be exceeded if negative current is injected on adjacent pins.
6. Vin must not exceed PXS_VREG value if ProxSense is enabled, even on port B and D (PXS_TX), Vreg = 1.55 V.
7. R
8. Data guaranteed by Design, not tested in production.
44/62
Symbol
C
V
R
V
V
I
IO
lkg
hys
DD
PU
PU
IH
IL
(8)
= 3.0 V, T
pull-up equivalent resistor based on a resistive transistor (corresponding I
Input low level voltage
Input high level voltage
Schmitt trigger voltage hysteresis
Input leakage current
Weak pull-up equivalent resistor
I/O pin capacitance
Table 27.
1. Data based on characterization results, not tested in production.
2. Data based on characterization performed on the whole data memory (2 Kbytes).
I/O port pin characteristics
General characteristics
Subject to general operating conditions for V
unused pins must be kept at a fixed voltage: using the output mode of the I/O for example or
an external pull-up or pull-down resistor.
Standard I/O static characteristics
Endurance
Data retention
A
=
Parameter
−
40 to 85 °C unless otherwise specified.
Parameter
Data memory endurance & retention
(5)
T
T
300 kcycles at T
300 kcycles at T
(3)
(3)
A
A
= −40 to 85°C
= −40 to 125°C
(7)
(4)
Doc ID 022344 Rev 1
Conditions
A
A
V
= 85°c
= 125°c
V
SS
Standard I/Os
Standard I/Os
Standard I/Os
Standard I/Os
SS
Conditions
Rx, Tx I/Os
V
(1)(2)
≤
≤
IN
V
V
IN
=
IN
V
≤
≤
SS
V
DD
V
reg
DD
(6)
and T
0.70 x V
PU
A
V
unless otherwise specified. All
SS
300
current characteristics.
Min.
−1
30
-1
Min.
30
-
-
−0.3
5
(1)
(1)(2)
(1)
DD
Typ.
Typ.
200
45
5
-
-
-
-
-
-
-
0.3 x V
V
Max.
DD
Max.
-
-
-
60
STM8TL53xx
1
1
-
-
+0.3
DD
kcycles
Years
Unit
Unit
mV
uA
kΩ
pF
V