TMP86xy44UG Toshiba, TMP86xy44UG Datasheet - Page 62

• Manufacturer Part Number: TMP86xy44UG
• Manufacturer: Toshiba

Specifications of TMP86xy44UG

• Package: QFP44
• Rom Types (m=mask,p=otp,f=flash): M/P
• Rom Size: 60
• Ram Size: 1K
• Driver Led: 19
• Driver Lcd: -
• Spi/sio Channels: 1
• Uart/sio Channels: 1
• I2c/sio Channels: -
• High-speed Serial Output: -
• Adc 8-bit Channels: -
• Adc 10-bit Channels: 8
• Da Converter Channels: 1
• Timer Counter 18-bit Channel: -
• Timer Counter 16-bit Channel: 2
• Timer Counter 8-bit Channel: 2
• Motor Channels: -
• Watchdog Timer: Y
• Dual Clock: Y
• Clock Gear: -
• Number Of I/o Ports: 35
• Power Supply (v): 4.5 to 5.5

5.4 Port P3 (P37 to P30)
(000EH)
(0003H)
control. Port P3 is also used as an analog input, key on wake up input. Input/output mode is specified by the corre-
sponding bit in the port P3 input/output control register (P3CR), and AINDS (bit 4 in ADCCR1). During reset,
P3CR are initialized to “0” and AINDS is set to “1”, therefore port P3 is configured as an input.
“0”. When AINDS is “0”, the pin which is specified as an analog input is used as analog input independent on the
value of P3CR and P3DR.
ifying as an analog input.
“0”. and the data of port which is not selected as an analog input is read “0” or “1”, depend on the voltage level.
Data can be written into the output latch regardless of P3CR contents, therefore initial output data should be written
into the output latch before setting P3CR.
cuted to keep a precision. In addition, a variable signal should not be input to an adjacent port to the analog input
during AD conversion.
P3DR
P3CR
R/W
Port P3 is an 8-bit input/output port which can be configured as an input or an output in one-bit unit under software
When used as an analog input, set an analog input channel to SAIN (bit 0, 1, 2 in ADCCR1) and clear AINDS to
When used as an input port or key on wake up input, the corresponding bit of P3CR is cleared to “0” without spec-
When the AD converter is enabled (AINDS is “0”), the data of port which is selected as an analog input is read
When used as an output port, the corresponding bit of P3CR is set to “1” without specifying as an analog input.
The pins not used as analog input can be used as an input/output port. But output instructions should not be exe-
Note: Ports set to the input mode read the pin states. Ports set to the output mode read the output latch. When input pin and out-
put pin exist in port P3 together, the contents of the output latch which is specified as an input mode may be rewritten by
executing the bit manipulation instructions.
STOP5
AIN7
P37
P3CR
7
7
Data output (P3DR)
Data input (P3DR)
STOP4
Key on wake up
AIN6
P36
6
6
I/O control
(Specified for each bit)
Analog input
P3CRi input
STOPjEN
OUTEN
AINDS
P3CRi
STOP3
STOP
SAIN
AIN5
P35
5
5
STOP2
AIN4
P34
Output latch
Output latch
4
4
D
D
Figure 5-5 Port P3
Q
Q
AIN3
P33
0: Input mode
1: Output mode
3
3
Page 51
AIN2
P32
2
2
AIN1
P31
1
1
AIN0
P30
0
0
(Initial value: 0000 0000)
(Initial value: 0000 0000)
P3i
Note: i = 7
j = 5 to 2
to
0
TMP86CS44UG
R/W