LPC2460 NXP Semiconductors, LPC2460 Datasheet - Page 14

• Manufacturer Part Number: LPC2460
• Description: Flashless 16-bit/32-bit Micro; Ethernet, Can, Isp/iap, Usb 2.0 Device/host/otg, External Memory Interface
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 4.
LPC2460_2
Preliminary data sheet
Symbol
P1[25]/
USB_LS1/
USB_HSTEN1/
MAT1[1]
P1[26]/
USB_SSPND1/
PWM1[6]/
CAP0[0]
P1[27]/
USB_INT1/
USB_OVRCR1/
CAP0[1]
P1[28]/
USB_SCL1/
PCAP1[0]/
MAT0[0]
P1[29]/
USB_SDA1/
PCAP1[1]/
MAT0[1]
P1[30]/
USB_PWRD2/
V
P1[31]/
USB_OVRCR2/
SCK1/AD0[5]
P2[0] to P2[31]
P2[0]/PWM1[1]/
TXD1/
TRACECLK
P2[1]/PWM1[2]/
RXD1/
PIPESTAT0
BUS
/AD0[4]
Pin description
Pin
80
82
88
90
92
42
40
154
152
[1]
[1]
[1]
[1]
[1]
[2]
[2]
[1]
[1]
…continued
Ball
T10
R10
T12
T13
U14
P2
P1
B17
E14
[2]
[2]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
Type
I/O
O
O
O
I/O
O
O
I
I/O
I
I
I
I/O
I/O
I
O
I/O
I/O
I
O
I/O
I
I
I
I/O
I
I/O
I
I/O
I/O
O
O
O
I/O
O
I
O
Rev. 02 — 1 February 2008
Description
P1[25] — General purpose digital input/output pin.
USB_LS1 — Low-speed status for USB port 1 (OTG transceiver).
USB_HSTEN1 — Host Enabled status for USB port 1.
MAT1[1] — Match output for Timer 1, channel 1.
P1[26] — General purpose digital input/output pin.
USB_SSPND1 — USB port 1 Bus Suspend status (OTG transceiver).
PWM1[6] — Pulse Width Modulator 1, channel 6 output.
CAP0[0] — Capture input for Timer 0, channel 0.
P1[27] — General purpose digital input/output pin.
USB_INT1 — USB port 1 OTG transceiver interrupt (OTG transceiver).
USB_OVRCR1 — USB port 1 Over-Current status.
CAP0[1] — Capture input for Timer 0, channel 1.
P1[28] — General purpose digital input/output pin.
USB_SCL1 — USB port 1 I
PCAP1[0] — Capture input for PWM1, channel 0.
MAT0[0] — Match output for Timer 0, channel 0.
P1[29] — General purpose digital input/output pin.
USB_SDA1 — USB port 1 I
PCAP1[1] — Capture input for PWM1, channel 1.
MAT0[1] — Match output for Timer 0, channel 0.
P1[30] — General purpose digital input/output pin.
USB_PWRD2 — Power Status for USB port 2.
V
Note: This signal must be HIGH for USB reset to occur.
AD0[4] — A/D converter 0, input 4.
P1[31] — General purpose digital input/output pin.
USB_OVRCR2 — Over-Current status for USB port 2.
SCK1 — Serial Clock for SSP1.
AD0[5] — A/D converter 0, input 5.
Port 2: Port 2 is a 32-bit I/O port with individual direction controls for each
bit. The operation of port 2 pins depends upon the pin function selected
via the Pin Connect block.
P2[0] — General purpose digital input/output pin.
PWM1[1] — Pulse Width Modulator 1, channel 1 output.
TXD1 — Transmitter output for UART1.
TRACECLK — Trace Clock.
P2[1] — General purpose digital input/output pin.
PWM1[2] — Pulse Width Modulator 1, channel 2 output.
RXD1 — Receiver input for UART1.
PIPESTAT0 — Pipeline Status, bit 0.
BUS
— Monitors the presence of USB bus power.
2
2
C serial clock (OTG transceiver).
C serial data (OTG transceiver).
Fast communication chip
LPC2460
© NXP B.V. 2008. All rights reserved.
14 of 68