OM6213 NXP Semiconductors, OM6213 Datasheet - Page 5

• Manufacturer Part Number: OM6213
• Description: Om6213 48 X 84 Pixels Matrix Lcd Driver
• Manufacturer: NXP Semiconductors

Philips Semiconductors
6
7
7.1
These pads output the row signals.
7.2
These pads output the column signals.
7.3
V
to as V
V
7.4
V
analog supply; jointly referred to as V
must be connected together.
2001 Nov 07
V
V
V
V
V
V
V
V
SCLK
T7
SDIN
D/C
SCE
OSC
V
T4
T5
T6
V
SS1
SS
DD1
SYMBOL
OS4
OS3
OS2
OS1
OS0
DD1
DD3
DD2
SS2
SS1
48
, V
PINNING
PIN FUNCTIONS
and V
provides the logic supply. V
SS1
ROW 0 to ROW 47 row driver outputs
COL 0 to COL 83 column driver outputs
V
SS
V
SS1
DD1
. When a pin has to be connected externally to
84 pixels matrix LCD driver
should be used.
SS2
and V
to V
must be connected together, jointly referred
13 to 18
19 to 22
23 to 30
32 to 35
36 to 39
43 to 50
54 to 61
DD3
PAD
31
40
41
42
51
52
53
SS2
3
4
5
6
7
: positive power supply rails
: negative power supply rails
V
V
V
V
V
supply voltage 1
supply voltage 3
supply voltage 2
serial clock input
test 7 alternative HV-gen
programming input
serial data input and HV-gen
programming input
data/command input
chip enable input (active
LOW)
oscillator input
ground 2
test 4 input
test 5 input
test 6 output
ground 1
LCD
LCD
LCD
LCD
LCD
offset pad 0 input
offset pad 1 input
offset pad 2 input
offset pad 3 input
offset pad 4 input
DD2
DESCRIPTION
and V
DD2
. V
DD3
DD2
provide the
and V
DD3
5
7.5
If the internal V
be connected together. If not (the internal V
is disabled and an external voltage is supplied at pin
V
must be connected to V
switch-off the charge pump if an external V
is used. V
7.6
Five input pins for on-glass V
connected to V
V
5-bit two’s complement number ranging from 16 to +15
decimal (from 10000 to 01111). The default value, with all
pins connected to V
is refreshed by each set bias system command or when
exiting the Power-down mode.
T1
T2
T3
V
V
V
RES
ROW 11 to
ROW 0
ROW 12 to
ROW 23
COL 0 to
COL 83
ROW 47 to
ROW 36
ROW 24 to
ROW 35
LCDIN
DD1
SYMBOL
LCDIN
LCDOUT
LCDSENSE
, which corresponds to logic 1. All five pins define a
), V
V
supplies
V
LCDOUT,
OS0
LCDIN
LCDOUT
to V
101 to 112 LCD row driver outputs
113 to 196 LCD column driver outputs
197 to 208 LCD row driver outputs
209 to 220 LCD row driver outputs
1, 8 to 12,
LCD
SS1
89 to 100 LCD row driver outputs
81 to 88,
is also used for HV-gen programming.
65 to 70
71 to 77
221 and
V
OS4
PAD
must be left open-circuit and V
222
LCDIN
, which corresponds to logic 0, or to
62
63
64
78
79
generator is used, then all 3 pins must
SS1
, is 0 decimal (00000). The register
LCDIN
and V
test 1 output
test 2 output
test 3 output
V
HV-gen programming input
V
V
input
reset input (active LOW)
dummy pads
. V
LCD
LCD
LCD
LCD
LCDSENSE
PR
supply voltage input and
generator output
generator regulation
offset. Each pin must be
must be set to logic 0 to
DESCRIPTION
Product specification
: LCD power
OM6213
LCD
LCD
generator
generator
LCDSENSE