SCA02010-TFN-LNN Shelly, Inc., SCA02010-TFN-LNN Datasheet

Page 1

... INNOVATIVE DISPLAY TECHNOLOGIES I RVINE P: 949-417-8070/F: 949-417-8075 E-mail: Website: Part Number : Customer APPROVED BY: ( FOR CUSTOMER USE ONLY ) SOLD BY APPROVED BY 17171 M A URPHY VENUE , C 92614-5915 ALIFORNIA info@shellyinc.com www.shellyinc.com Specification SCA02010-TFN-LNN : PCB VERSION: CHECKED BY DATE: ISSUE DATE ...

Page 2

NO. 1. Cover 2. Record of Revision 3. LCD Module Physical Data 4. External Dimensions 5. Block Diagram 6. Absolute Maximum Ratings 7. Electrical Characteristics 8. Interface PIN Connections 9. Recommend Initial Code 10. Electro-Optical Characteristics 11. Inspection Criterion 12. ...

Page 3

DATE PAGE 09/30/09 3 RECORD OF REVISION Added version #A402 SUMMARY ...

Page 4

LCD MODULE PHYSICAL DATA  General Description Size Display Type Display Mode Viewing Direction Connection Type Operation temperature Storage temperature Driving IC  Mechanical Description Item Number of dots LCM dimension Active area Dot size Dot pitch Backlight 2.0" ...

Page 5

EXTERNAL DIMENSIONS ...

Page 6

BLOCK DIAGRAM /LCD_RESET / D15 VDD IOVCC GND  Black Light Unite  ABSOLUTE MAXIMUM RATINGS G2 LCD 176(RGB)*220 G220 HX8340-B G1 G119 ...

Page 7

Item Operating temperature Storage temperature Power Supply Voltage Supply voltage for logic NOTE the module is used above these absolute maximum ratings. It may become permanently damaged. Using the module within the following electrical characteristic conditions are also ...

Page 8

ELECTRICAL CHARACTERISTICS  DC Characteristics Item Input high voltage Input low voltage Output high voltage Output low voltage Supply voltage for logic Driver Operating voltage The TFT LCD’s gate driver Current consumption for LCD normal operation  AC Characteristics ...

Page 9

INTERFACE PIN CONNECTIONS NO. Symbol 1 GND 2 VDD D10 17 ...

Page 10

Recommended Initial Code void init() { res=0; delay(20); res=1; delay(20); /*Power voltage setting*/ write_init(0x1f,0x03); write_init(0x20,0x00); write_init(0x24,0x30); write_init(0x25,0x3c); write_init(0x23,0x35); /*Power on setting*/ write_init(0x18,0x44); write_init(0x21,0x01); write_init(0x01,0x00); write_init(0x16,0x08); write_init(0x17,0x05); write_init(0x1c,0x03); write_init(0x19,0x06); delay(5); /* Driving ability setting*/ write_init(0x60,0x00); write_init(0x61,0x06); write_init(0x62,0x00); write_init(0x63,0xC8); write_init(0x73,0x70); /*Gamma ...

Page 11

GRAM area*/ write_init(0x02,0x00); write_init(0x03,0x00); write_init(0x04,0x00); write_init(0x05,0xaf); write_init(0x06,0x00); write_init(0x07,0x00); write_init(0x08,0x00); write_init(0x09,0xdb); /*Display on setting*/ write_init(0x26,0x84); delay(40); write_init(0x26,0xb8); delay(40); write_init(0x26,0xbc); write_command(0x22 ...

Page 12

ELECTRO-OPTICAL CHARACTERISTICS Driving condition: VDD= 2.8V, I Item Light angle（°） Temp（°C） Symbol Transmittance 0 Contrast ratio 0 Brightness 0 Luminance uniformity 0 (surface within panel) Cross talk 0 Rｘ Rｙ Gｘ Gｙ Chromaticity 0 Bｘ Bｙ Wｘ Wｙ Color ...

Page 13

Hor Ver. Y Note : (1). Transmittance Introduction Transmittance (diffuse transmission factor measure for the LCD panel transparency. The Light Source for this measurement is the accompanying LCD-module backlight system (LEDs, Lightguide…) Measurement conditions: Measuring ...

Page 14

Gmin: Luminance with all pixels black (3). Surface luminance uniformity within panel Measurement conditions: Measuring Equipment Measurement Point Diameter 3mm // 1mm Measurement Point Location Light Source Test pattern Measuring procedure: Measure the luminance Li with the points in figure ...

Page 15

Crosstalk is an effect where the contrast of a display pixel is influenced by the state of the related pixels. A measure for this effect is the Cross Talk Value (CTV) Measurement conditions: Measuring Equipment Measurement Point Diameter Measurement Point ...

Page 16

Determination of Crosstalk value (CTV) (5). NTSC Measurement conditions: Measuring Equipment Measuring Point Diameter Measuring point location Light source Test pattern Contrast setting Definitions Panel color coordinates according the CIE colour system (CIE 1931). In general always requested ...

Page 17

Color Gamut ...

Page 18

Brightness  INSPECTION CRITERION This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling method shall be in accordance with MIL-STD-105D, inspection level II and based on: Major defect: ...

Page 19

Zone A: character/Digit area Zone B: viewing area except Zone A (ZoneA+ZoneB=minimum Viewing area) Zone C: Outside viewing area (invisible area after assembly in customer’s product) Fig.1 Inspection zones in an LCD. Note general rule, visual defects in ...

Page 20

Dim Spots 2. Circle Size(mm) shaped and dim edged Φ ≤ 0.2 defects 0.20＜Φ ≤ 0.40 0.40＜Φ ≤ 0.60 0.60＜Φ 4.2. Cosmetic Defect Item Items to be inspected No Line defect L(Length) Black ...

Page 21

If the Polarizer scratch can be seen after mobile phone cover assembling or in the operating condition, judge by the line defect of 4.2.2. If the Polarizer scratch can be seen only in non-operating condition or some special angle, judge ...

Page 22

Chips on corner Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. (ii)Usual surface cracks 4.3.5 Glass defect (iii) Crack Cracks tend to break ...

Page 23

If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the substance contacts your skin or clothes, wash it ...

Page 24

Do not alter, modify or change the shape of the tab on the metal frame not make extra holes on the printed circuit board, modify its shape or change the positions of components to be attached. - ...

Page 25

A slight dew depositing on terminals is a cause for electro-chemical reaction resulting in terminal open circuit. Usage under the maximum operating temperature, 50%RH or less is required. (6) Input each signal after the positive/negative voltage becomes stable. (7) ...