SCA04310-BFN-LNN Shelly, Inc., SCA04310-BFN-LNN Datasheet

Page 1

... INNOVATIVE DISPLAY TECHNOLOGIES I RVINE P: 949-417-8070/F: 949-417-8075 E-mail: Website: Part Number : Customer APPROVED BY: ( FOR CUSTOMER USE ONLY ) SOLD BY APPROVED BY 17171 M A URPHY VENUE , C 92614-5915 ALIFORNIA info@shellyinc.com www.shellyinc.com Specification SCA04310-BFN-LNN : PCB VERSION: CHECKED BY DATE: ISSUE DATE ...

Page 2

NO. 1. Cover 2. Record of Revision 3. LCD Module Physical Data 4. External Dimensions 5. Block Diagram 6. Absolute Maximum Ratings 7. Electrical Characteristics 8. Interface PIN Connections 9. Electro-Optical Characteristics 10. Inspection Criterion 11. Precautions for Using LCD ...

Page 3

DATE PAGE P4 2009/06/24 P9 2009/10/30 RECORD OF REVISION SUMMARY Update LCM drawing Add electro-optical characteristics Added revision #A401 ...

Page 4

LCD MODULE PHYSICAL DATA  General Description Size Display Type Display Mode Viewing Direction Connection Type Operation temperature Storage temperature Driving IC  Mechanical Description Item Number of dots LCM dimension Active area Dot size Dot pitch Backlight 4.3" ...

Page 5

EXTERNAL DIMENSIONS ...

Page 6

BLOCK DIAGRAM DISP PCLK DE HSYNC VSYNC R0-R7 G0-G7 B0-B7 DISP DE VDD GND  Black Light Unite G2 LCD 480(RGB)*272 G272 HX8257 G1 G271 ...

Page 7

ABSOLUTE MAXIMUM RATINGS Item Operating temperature Storage temperature Power Supply Voltage NOTE the module is used above these absolute maximum ratings. It may become permanently damaged. Using the module within the following electrical characteristic conditions are also ...

Page 8

ELECTRICAL CHARACTERISTICS  DC Characteristics Item Input high voltage Input low voltage Supply voltage(1) Supply voltage(2) Logic dynamic current Driver dynamic current  Back-Light unit Item Current CIE Luminous Uniformity Ratio Bezel(BE) must be connected to ground of the ...

Page 9

INTERFACE PIN CONNECTIONS NO. Symbol 1 VLED- 2 VLED+ 3 GND 4 VDD ...

Page 10

ELECTRO-OPTICAL CHARACTERISTICS Driving condition: VDD=3.3V, I Item Light angle（°） Temp（°C） Symbol Transmittance 0 Contrast ratio 0 Brightness 0 Luminance uniformity 0 (surface within panel) Cross talk 0 Rｘ Rｙ Gｘ Gｙ Chromaticity 0 Bｘ Bｙ Wｘ Wｙ Color Reproduction ...

Page 11

Measuring Equipment Measurement Point Diameter Measurement Point Location Light source Reflectance Plate Test pattern Contrast setting Measuring procedure: Transmittance: The light source is located at the backside of the panel. 1、 Measure the light source 2、 Place the LCD panel ...

Page 12

Measure the luminance Li with the points in figure 1. Figure Active Area Uniformity value (Lu): min max( ) (4)．CROSS-TALK Introduction： Crosstalk is an effect where the contrast of ...

Page 13

Pattern (valid for all greyscales): W: The width of the rectangle in the following pictures; 5mm 2*w=10mm Pattern A ● Definitions： Cross Talk Value： CTV = |LvA - LvB| / LvA * 100% Where： LvA: Luminance measured with the ...

Page 14

Definitions Panel colour coordinates according the CIE colour system (CIE 1931). In general always requested to measure the X, Y and Z values. Here u´, v´ and L* are according CIE 1931 ...

Page 15

Color Gamut Ratio (NTSC) related to NTSC’: NTSC: =F (display)/F (NTSC’) NTSC’ primaries: Red Green Blue F (NTSC’) =74.42 12:00 9:00 6:00 Brightness x’ y’ 0.67 0.33 0.21 0.71 0.14 0.08 3:00 Brightness cure of selected segment B 2 Brightness ...

Page 16

INSPECTION CRITERION This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling method shall be in accordance with MIL-STD-105D, inspection level II and based on: Major defect: AQL ...

Page 17

Inspection standards 4.1 Major Defect Item Items to be inspected display 4.1.1 All 2) Display abnormally functional defects 3) Missing vertical，horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. 4.1.2 Missing Missing ...

Page 18

Cosmetic Defect Ite Items inspected No Line defect L(Length) Black line, White line, Foreign 4.2.2 material under polarizer, If the Polarizer scratch can be seen after mobile phone cover assembling or in the operating condition, judge ...

Page 19

Cosmetic Defect Item Items to be inspected No (i) Chips on corner Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. (ii)Usual surface cracks ...

Page 20

PRECAUTIONS FOR USING LCD MODULES Handing Precautions (1) The display panel is made of glass and polarizer. As glass is fragile, it tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Do ...

Page 21

LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it. - ...

Page 22

Precautions for Operation (1) Viewing angle varies with the change of liquid crystal driving voltage (VLCD). Adjust VLCD to show the best contrast. ( indispensable condition to drive LCD's within the specified voltage limit since the higher ...