SCA03510-BFN-LRN Shelly, Inc., SCA03510-BFN-LRN Datasheet

Page 1

... INNOVATIVE DISPLAY TECHNOLOGIES I RVINE P: 949-417-8070/F: 949-417-8075 E-mail: Website: Part Number : Customer APPROVED BY: ( FOR CUSTOMER USE ONLY ) SOLD BY APPROVED BY 17171 M A URPHY VENUE , C 92614-5915 ALIFORNIA info@shellyinc.com www.shellyinc.com Specification SCA03510-BFN-LRN : PCB VERSION: CHECKED BY DATE: ISSUE DATE ...

Page 2

NO. 1. Cover 2. Record of Revision 3. LCD Module Physical Data 4. External Dimensions 5. Block Diagram 6. Absolute Maximum Ratings 7. Electrical Characteristics 8. Touch Screen Panel Specifications 9. Interface PIN Connections 10. Recommend Initial Code 11. Electro-Optical ...

Page 3

DATE PAGE P11 2009/04/21 P13 2009/07/07 P4 2009/10/30 P3 RECORD OF REVISION Update initial code Add electro-optical characteristics Update LCM drawing Added version # A802 SUMMARY ...

Page 4

LCD MODULE PHYSICAL DATA  General Description Display Type Display Mode Viewing Direction Connection Type Operation temperature Storage temperature Driving IC  Mechanical Description Item Number of dots LCM dimension TP outline LCD outline Active area Dot size Dot ...

Page 5

EXTERNAL DIMENSIONS TP) 3  BLOCK DIAGRAM 3 56( 52. * VA/ 05( 55. * 85( 55 61. 6( 63. Ó 0 ...

Page 6

TFT-LCD Module (Interface System Structure) G2 G240 RESET SPCK SPDA CLK DEN D00~ D23 VCC GND ANODE CATHODE LCD 320(RGB)*240 G239 HX8238 Black Light Unite Touch Screen Panel ...

Page 7

Black Light Unite VLED VLED  Touch Screen Panel(Top View)  ABSOLUTE MAXIMUM RATINGS Item Operating temperature Storage temperature Input voltage Supply voltage Supply voltage for LCD NOTE the module is used above these absolute maximum ratings. ...

Page 8

ELECTRICAL CHARACTERISTICS  DC Characteristics Vss= 0V, Ta= 25℃ Item Power supply LCD driving voltage Current consumption for LCD normal operation  Back-Light unit Item Current CIE Brightness Luminous Uniformity Ratio Note: 1. Average Luminous Uniformity ...

Page 9

Characteristics Item Linearity Terminal Resistance Insulation Resistance Operating voltage Response Tine Transmittance Note not operate it with a thing except a polyacetal pen(tip R0.8mm or less finger, especially those with hard or sharp tips ...

Page 10

NO. Symbol 1 GLED 2 GLED 3 VLED 4 VLED 5 GND GND POL 14 RESET 15 SPENA 16 SPCK 17 SPDI 18 D00 19 D01 ...

Page 11

D18 37 D19 38 D20 39 D21 40 D22 41 D23 42 IHS 43 IVS 44 CLK VCC 48 VCC ...

Page 12

RECOMMENDED INITIAL CODE void WriteRegHX8238(unsigned int reg) { int i,tmp; CS(0); tmp=0x70;//01110000//RS=0,RW=0 for(i=7;i>=0;i--) { SCL(0); SDI((tmp>>i)&0x01); SCL(1); } for(i=15;i>=0;i--) { SCL(0); SDI((reg>>i)&0x01); SCL(1); } CS(1); } void WriteDatHX8238(unsigned int dat) { int i,tmp; CS(0); tmp=0x72;//01110010//RS=1,RW=0 for(i=7;i>=0;i--) { SCL(0); SDI((tmp>>i)&0x01); ...

Page 13

WriteRegHX8238(0x0002);//LCD-Driving-Waveform Control WriteDatHX8238(0x0200);//B/C=1,NW7-0=0 WriteRegHX8238(0x0003);//Power control 1 WriteDatHX8238(0x7166);//0x7664 0xa164 WriteRegHX8238(0x0004);//Input Data and Color Filter Control WriteDatHX8238(0x0447);//SWD2-0=111,SEL2-0=000, WriteRegHX8238(0x0005);//Function Control WriteDatHX8238(0xBCD4);//0xbcd4 0xfcd4 0xb4d4 WriteRegHX8238(0x000A);//Contrast/Brightness Control WriteDatHX8238(0x3F08);//0x4008 WriteRegHX8238(0x000B);//Frame Cycle Control WriteDatHX8238(0xD400);//0xd400 0xc400 0xc470 WriteRegHX8238(0x000D);//Power Control 2 WriteDatHX8238(0x123A);//VLCD63,0x123a 0x123f WriteRegHX8238(0x000E);//Power control 3 WriteDatHX8238(0x3100);//VCOMA,0x2c00 0x3500 0x3000 ...

Page 14

ELECTRO-OPTICAL CHARACTERISTICS Driving condition: VDD=2.8V, I Item Light angle（°） Temp（°C） Symbol Transmissive 0 Contrast ratio 0 Brightness 0 Luminance uniformity 0 (surface within panel) Cross talk 0 Rｘ Rｙ Gｘ Gｙ Chromaticity 0 Bｘ Bｙ Wｘ Wｙ Color Reproduction ...

Page 15

Measurement conditions: Measuring Equipment Measurement Point Diameter Measurement Point Location Light source Reflectance Plate Test pattern Contrast setting Measuring procedure: Transmittance: The light source is located at the backside of the panel. 1、 Measure the light source 2、 Place the ...

Page 16

Measure the luminance Li with the points in figure 1. Figure Active Area Uniformity value (Lu): max( ) min (4)．CROSS-TALK Introduction： Crosstalk is an effect where the contrast of ...

Page 17

W: The width of the rectangle in the following pictures; 5mm 2*w=10mm Pattern A ● Definitions： Cross Talk Value： CTV = |LvA - LvB| / LvA * 100% Where： LvA: Luminance measured with the centre test point of pattern A ...

Page 18

Definitions Panel colour coordinates according the CIE colour system (CIE 1931). In general always requested to measure the X, Y and Z values. Here u´, v´ and L* are according CIE 1931 ...

Page 19

NTSC: =F (display)/F (NTSC’) NTSC’ primaries: Red Green Blue F (NTSC’) =74.42 12:00 9:00 6:00 Brightness x’ y’ 0.67 0.33 0.21 0.71 0.14 0.08 3:00 Brightness cure of selected segment B 2 Brightness curve of nonselected segment B 1 Driving ...

Page 20

INSPECTION CRITERION This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling method shall be in accordance with MIL-STD-105D, inspection level II and based on: Major defect: AQL ...

Page 21

Inspection standards 4.1 Major Defect Item Items to be inspected display 4.1.1 All 2) Display abnormally functional defects 3) Missing vertical，horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. 4.1.2 Missing Missing ...

Page 22

Cosmetic Defect Item Items to be inspected No Line defect L(Length) Black line, White line, Foreign 4.2.2 material under polarizer, If the Polarizer scratch can be seen after mobile phone cover assembling or in the operating condition, judge by ...

Page 23

Cosmetic Defect Item Items to be inspected No (i) Chips on corner Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. (ii)Usual surface cracks ...

Page 24

PRECAUTIONS FOR USING LCD MODULES Handing Precautions (1) The display panel is made of glass and polarizer. As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Do ...

Page 25

The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated （13）Since LCM has been assembled and adjusted with a high degree of ...

Page 26

Viewing angle varies with the change of liquid crystal driving voltage (VLCD). Adjust VLCD to show the best contrast. ( indispensable condition to drive LCD's within the specified voltage limit since the higher voltage then the ...